Bosch Rexroth GTE Series Скачать руководство пользователя

Страница: 14 / 88

1) to be trained, instructed or authorized to switch electric circuits and devices

safely on and off, to ground them and to mark them
2) to be trained or instructed to maintain and use adequate safety equipment
3) to attend a course of instruction in first aid

User

A user is a person installing, commissioning or using a product which has been

placed on the market.

3.2

General Information

3.2.1

Using the Safety Instructions and Passing Them on to Others

Do not attempt to install and operate the components of the electric drive and

control system without first reading all documentation provided with the product.

Read and understand these safety instructions and all user documentation prior

to working with these components. If you do not have the user documentation

for the components, contact your responsible Rexroth sales partner. Ask for

these documents to be sent immediately to the person or persons responsible

for the safe operation of the components.
If the component is resold, rented and/or passed on to others in any other form,

these safety instructions must be delivered with the component in the official

language of the user's country.
Improper use of these components, failure to follow the safety instructions in

this document or tampering with the product, including disabling of safety de‐

vices, could result in property damage, injury, electric shock or even death.

3.2.2

Requirements for Safe Use

Read the following instructions before initial commissioning of the components

of the electric drive and control system in order to eliminate the risk of injury

and/or property damage. You must follow these safety instructions.
●

Rexroth is not liable for damages resulting from failure to observe the

safety instructions.

●

Read the operating, maintenance and safety instructions in your language

before commissioning. If you find that you cannot completely understand

the application documentation in the available language, please ask your

supplier to clarify.

●

Proper and correct transport, storage, mounting and installation, as well

as care in operation and maintenance, are prerequisites for optimal and

safe operation of the component.

●

Only qualified persons may work with components of the electric drive and

control system or within its proximity.

●

Only use accessories and spare parts approved by Rexroth.

●

Follow the safety regulations and requirements of the country in which the

components of the electric drive and control system are operated.

●

Only use the components of the electric drive and control system in the

manner that is defined as appropriate. See chapter "Appropriate Use".

●

The ambient and operating conditions given in the available application

documentation must be observed.

●

Applications for functional safety are only allowed if clearly and explicitly

specified in the application documentation "Integrated Safety Technolo‐

gy". If this is not the case, they are excluded. Functional safety is a safety

Bosch Rexroth AG

DOK-GEAR**-GTE********-PR06-EN-P

Rexroth GTE Planetary Gearboxes

12/85

Safety Instructions for Electric Drives and Controls

LSA Control S.L. www.lsa-control.com [email protected] (+34) 960 62 43 01

Содержание Rexroth GTE Series

























































































Результаты поиска

Содержание Rexroth GTE Series

Отзывы:

Похожие инструкции для Rexroth GTE Series

Бренды по названию

Популярные бренды

Bosch Rexroth GTE Series, Руководство по планированию проекта

Результаты поиска

Содержание Rexroth GTE Series

Отзывы:

Похожие инструкции для Rexroth GTE Series

Бренды по названию

Популярные бренды