Bosch Rexroth ctrlX SAFETY SAFEX-C.12 Скачать руководство пользователя страница 41

Страница: 41 / 84

ctrlX SAFETY

| Device type SAFEX-C.12

41/83

DOK-XSAFE*-SAFEX-C.1XC-IT03-EN-P, Edition 03, Bosch Rexroth AG

9.1.4

Ambient data

Tabelle 22:

Ambient data

Value 1

Value 2

Temperature

0 °C ... +50 °C during operation

-40 °C ... +70 °C for storage
(without condensation)

Protection rating

IP 20 according to EN 60529,
IP00 connector

Climate category

3K22 according to DIN EN
60721-3-3

Pollution category

2 according to DIN EN 60664-
1:2007

Minimum, maximum relative
humidity (non-condensing)

8 % … 95 %

1 g/m³ … 29 g/m³

Mechanical resistance

Shock resistance:

EN 61800-2, IEC 60721-3-3
Class 3M1; 19.6 m/s²

Vibration:

IEC 61131-2; 5-8.4 Hz with
3.5 mm amplitude; 8.4-150
Hz with 1 g peak
acceleration

Free fall (shipping package)

1 m

Max. installation height

≤

3000 m above sea level

Discharge of static electricity

ESD resistance according to EN 61000-6-7

•

Criterion: according to IEC 61000-4-2

•

Test voltage: 4 kV/8 kV Contact/Air

NOTE

Failure of the product due to contaminated air



The ambient air must be free of higher concentrations of acids, alkalis, corrosive agents,

salt, metal vapors and other electrically conductive impurities.



The devices must be installed in housings or installation spaces with a protection rating

of at least IP 54 according to DIN EN 60529.

Содержание Rexroth ctrlX SAFETY SAFEX-C.12





















































































Результаты поиска

Содержание Rexroth ctrlX SAFETY SAFEX-C.12

Отзывы:

Похожие инструкции для Rexroth ctrlX SAFETY SAFEX-C.12

Бренды по названию

Популярные бренды

Bosch Rexroth ctrlX SAFETY SAFEX-C.12, Руководство по эксплуатации

Результаты поиска

Содержание Rexroth ctrlX SAFETY SAFEX-C.12

Отзывы:

Похожие инструкции для Rexroth ctrlX SAFETY SAFEX-C.12

Бренды по названию

Популярные бренды