manualshive.com logo in svg

Bosch Rexroth A10VG, Инструкция по эксплуатации

Поделиться
Скачать
Bosch Rexroth A10VG Скачать руководство пользователя страница 60

60/64 Troubleshooting

Bosch Rexroth AG

, Series 10 A10VG, RE 92750-01-B/06.2018

Table 13: Axial piston unit malfunction table

Malfunction

Possible cause

Remedy

Pressure/flow fluctuations or 
instabilities

Insufficient air bleeding of the hydraulic system

Fill the axial piston unit, suction line for the 
hydraulic pump and the reservoir
Completely air bleed the axial piston unit and 
hydraulic system
Check correct installation position

Insufficient suction conditions, e.g., insufficient 
dimensioning of the suction line, viscosity of 
the hydraulic fluid too high, suction height too 
high, suction pressure too low, foreign particles 
in the suction line, suction filter too small or 
blocked, etc.

Machine/system manufacturer: Check the 
system, e.g., optimize inlet conditions, use 
suitable hydraulic fluid
Fill the suction line with hydraulic fluid

Remove foreign particles from the suction line

Check the filter system and change the filter as 
necessary

Oscillate pressure limiting and control valves in 
the axial piston unit (boost-pressure relief valve, 
high-pressure relief valve, pressure cut-off, 
pressure reducing valve)

Air bleed the axial piston unit and hydraulic 
system
Contact Bosch Rexroth Service

Unstable control signal

Contact machine/system manufacturer or  
Bosch Rexroth Service

Malfunction in the control devices or the 
controller

Contact Bosch Rexroth Service

Excessively high temperature of 
hydraulic fluid and housing

Excessively high inlet temperature at the axial 
piston unit

Machine/system manufacturer: Inspect system, 
e.g., malfunction in the cooler, insufficient 
hydraulic fluid in the reservoir

Wrong setting or malfunction of the pressure 
relief and pressure control valves (e.g., high-
pressure relief valve, pressure cut-off, pressure 
reducing valve)

Optimize the adjustment of the pressure 
limitation and pressure control valves of the 
axial piston unit and the pressure safeguarding 
in the hydraulic system
Contact Bosch Rexroth Service

Contact machine/system manufacturer

Flushing flow of the flushing valve too low

Contact Bosch Rexroth Service

Axial piston unit worn

Replace axial piston unit; contact  
Bosch Rexroth Service

Содержание Rexroth A10VG

































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды