manualshive.com logo in svg

Bosch Rexroth A10VG, Инструкция по эксплуатации

Поделиться
Скачать
Bosch Rexroth A10VG Скачать руководство пользователя страница 16

16/64 

General notices regarding property and product damage

Bosch Rexroth AG

, Series 10 A10VG, RE 92750-01-B/06.2018

3  General notices regarding property and 

product damage

The following instructions apply to chapters 6 to 14.

NOTICE

Danger from improper handling!
Product can be damaged!

 

▶

Do not subject the product to improper mechanical loads.

 

▶

Never grab or climb onto the product.

 

▶

Do not place/lay any objects on the product.

 

▶

Do not strike the drive shaft of the axial piston unit.

 

▶

Do not set/place the axial piston unit on the drive shaft or assembled parts.

 

▶

Do not strike assembled parts (e.g., sensors or valves).

 

▶

Do not strike sealing surfaces (e.g., working ports).

 

▶

Leave the protective covers on the axial piston unit until you connect the lines.

 

▶

Disconnect all electrical connectors before arc welding or painting.

 

▶

Make sure the electronic components (e.g., sensors) do not build up 
electrostatic charges (e.g., during painting).

Risk of property damage due to inadequate lubrication!
Product can be damaged or destroyed!

 

▶

Never operate the axial piston unit with insufficient hydraulic fluid. Specifically, 
make sure the rotary group has sufficient lubrication.

 

▶

When commissioning a machine/system, make sure that the housing area and 
the working lines of the axial piston unit are filled with hydraulic fluid and 
remain filled during operation. Avoid air inclusions in the forward drive shaft 
bearing, especially with the axial piston unit installed with the drive shaft up.

 

▶

Check the hydraulic fluid level in the housing regularly and recommission, if 
necessary. For above-reservoir installation, the housing may drain out through 
the drain line after prolonged standstill periods (air enters through the shaft 
seal) or through the working line (gap leakage). This means the bearings are 
insufficiently lubricated when the system is turned on.

 

▶

Make sure the suction line is always filled with hydraulic fluid during 
commissioning and operation.

Mixing hydraulic fluids!
Product can be damaged!

 

▶

Before installation, remove all fluids from the axial piston unit to prevent mixing 
with the hydraulic fluid used in the machine/system.

 

▶

Never mix hydraulic fluids from different manufacturers or different types from 
the same manufacturer.

Содержание Rexroth A10VG

































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды