Bosch Rexroth A10VG Скачать руководство пользователя | Manualshive

Страница: 37 / 64

background image

Installation 37/64

RE 92750-01-B/06.2018, A10VG, Series 10,

Bosch Rexroth AG

No gearing forces higher than the permissible axial and radial forces should act on
the shaft; if necessary, support the gear wheel at the gearbox output separately.

7.4.6 Installation with cardan shaft
The following describes how to connect the axial piston unit to the drive motor with
a cardan shaft.

nOTICE! Damage to the axial piston unit and leaks at the shaft seal!
Improperly installed cardan shafts generate unbalances. This results in vibrations
and excessive forces on the drive shaft.

▶

Observe the cardan shaft manufacturer's assembly instructions.

1.

Position the axial piston unit close to the specified installation location. Allow
enough space for the cardan shaft to fit through on both sides.

2.

Place the cardan shaft on the output shaft of the drive motor.

3.

Push the axial piston unit to the cardan shaft and place the cardan shaft on the
drive shaft of the axial piston unit.

4.

Bring the axial piston unit to the installation position and fasten it. If necessary,
details on the required tools and tightening torque for the mounting bolts can be
obtained from the system manufacturer.

7.4.7 Completing installation

1.

Remove any installed transport screws.

CAUTIOn! Operation with protective plugs!
Operating the axial piston unit with protective plugs may result in injury or damage
to the axial piston unit.

▶

Before commissioning, remove all protective plugs and replace them with
suitable, pressure-resistant, metal threaded plugs or connect the appropriate
lines.

2.

Remove the transport protection.
The axial piston unit comes with protective covers (1), (3) and protective
plugs (2). They are not pressure-resistant and have to be removed prior to
connection. Use a suitable tool for this to prevent damage to the sealing and
functional surfaces. If sealing or functional surfaces are damaged, contact your
Bosch Rexroth service partner or the service department of the factory that
manufactured the axial piston unit.

For attachment via gear

wheel or helical gear shaft

«
...
35
36
37
38
39
...
»

Содержание Rexroth A10VG

































































Отзывы:

Нет отзывов

Похожие инструкции для Rexroth A10VG

Бренд: Xylem Страницы: 44

Бренд: salmson Страницы: 20

Бренд: Vagner Pool Страницы: 35

1 EPBH 9.2-11 T-AVS

Бренд: EBARA Страницы: 16

Бренд: Simer Страницы: 35

Бренд: Pentair Страницы: 8

SOGEVAC SV100 B

Бренд: LEYBOLD Страницы: 44

Бренд: Cala Страницы: 21

Well Wizard 1100 Series

Бренд: QED Страницы: 24

Бренд: SHIMGE Страницы: 24

Бренд: Laars Страницы: 40

Бренд: Samoa Страницы: 24

Comfort Solutions 1900e Series

Бренд: Taco Страницы: 12

Бренд: Beretta Страницы: 24

Бренд: Power Fist Страницы: 2

Isotemp 602431B000000

Бренд: Indel Marine Страницы: 3

Aquantia KHPS-MO Series

Бренд: Kaysun Страницы: 92

Бренд: Lochinvar Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды