Bosch RDE182141M, Инструкция по установке и эксплуатации

Страница: 20 / 28

12 | English
6 720 820 328 - 9001217888 | (06.19)
Robert Bosch Hausgeräte GmbH
X
The mixer and the warm water pipe may
be hot. Please inform and instruct chil-
dren appropriately.
X
Do not use aggressive or abrasive clean-
ing detergents!
X
Do not use a steam cleaner.
X
The appliance is only to be descaled by
a suitably qualified specialist.
Congratulations on purchasing this Bosch appliance. You
have acquired a top-quality product, which will give you
a lot of enjoyment.
Installation instructions
These installation instructions apply to various
continuous-flow heater appliance models. Therefore the
illustrations may deviate from the device you bought.
X
Install the appliance as shown in the illustrations. The
illustrations can be found in the centre of the instruc-
tion manual. Observe the instructions in the text.
Installation
Unpacking/Removing the cover (Figure I)
X
Unpack the appliance and check for transport
damage. If any components are damaged, then do not
connect the appliance.
X
Check that your appliance contains all components
included in the scope of delivery: appliance,
installation set with supplementary sheets,
installation instructions, operating instructions.
X
Please dispose of the packaging and the old
appliance in an environmentally-friendly manner.
X
When removing the cover from either a Type A or
Type B appliance, please note the following:
The Type A cover is fastened by a central closure be-
hind the service flap.
The Type B cover is attached by two screws located
on the underside of the cover.
Preparations for installation (Figure II)
Important: Only use the supplied installation set.
The supplied water connection nozzles must be installed!
X
Shut off water supply. The electrical connection (con-
nection cable) must be disconnected from the power
supply. Unscrew the fuse or switch off the circuit
breaker.
X
Install the water connection nozzles according to the
instructions on the supplementary sheet.
X
The electrical connection cable can either be guided
in at the top (X) or bottom (Y).
X
The rear panel must lie against the cold water con-
nection nozzle in the position provided for such
(Fig. II, 8.).
Wall mounting (Figure III)
X
The grommet must tightly surround the connection
cable. If it is damaged during mounting, the openings
must be provided with watertight sealing.
X
The electrical supply terminal can be fitted at the top
(X) or bottom (Y). The sheath of the connection cable
must extend for at least 40 mm into the appliance.
X
The distance to the wall is variable. You can compen-
sate for any unevenness of the wall’s surface. With
a distance to the wall of 8–16 mm, insert the spacer
and install the extender (Fig. III, 3. – 5.).
X
The appliance must be mounted securely on the wall.
If necessary, attach it at the lower adjustable screws
(Fig. III, 6.).
Water connection (Figure IV)
X
Connect the water supply, then open the cold water
supply.
X
The appliance must be vented. To do so, open the
warm water tap fully and flush out the appliance
thoroughly for 1 minute.
Electrical connection/Mounting
(Figure V)
X
Only for appliances with power selector switches:
Set the power using the power selector switch before
connecting the wires to the mains connection termi-
nal:
Nominal output power left, reduced output right
(Fig. V, 1.) and the set output marked on the ratings
plate.
X
Screw the wires tightly into the mains connection
terminal.
X
Switch on the safety limiter (Fig. V, 3.)
X
Install the cover – according to either Type A or B
instructions (Fig. V, 4. – 7.).
Installation note
X
The installation of non plug-in ready appliances
must be undertaken by the respective utility opera-
tor or by a qualified specialist company, who can
also assist you when you are requesting the ap-
proval of the utility company for installation of the
appliance.