Bosch R928057041 Скачать руководство пользователя | Manualshive

Страница: 12 / 46

background image

12/46

Set-up and connection

Bosch Rexroth AG

, RE 51550-B/09.2019

4 Set-up and connection

DANGER

Electrical voltage!
Danger of electric shock

▶

De-energize the plant.

▶

The device may only be installed, maintained and commissioned by
instructed, expert personnel.

▶

The applicable safety regulations of the place of use must be observed.

DANGER

Toxic, corrosive gases / liquids!
Protect yourself from toxic, corrosive gases/liquids during all work. Wear
appropriate protective equipment.

CAUTION

Overpressure!
Protect the device from static and dynamic overpressures.
Provide suitable measures for prevention!

4.1 Assembly

Before installing the device, make sure that the plant is depressurized, otherwise
liquid may escape. If necessary, use a collecting container. The WGM is delivered
completely assembled and can be screwed into the pipeline with the thread. Make
sure that the sensor part is always completely surrounded
by the medium in order to display correct measured values.

DANGER

Electrical voltage!
Danger of electric shock
When connecting the devices, the maximum admissible voltages and
currents (see technical data) must be observed and the required wire
cross-sections and circuit breakers must be dimensioned accordingly.
When selecting the connecting cables, the maximum admissible operating
temperatures of the devices must also be observed.

«
...
10
11
12
13
14
...
»

Содержание R928057041















































Отзывы:

Нет отзывов

Похожие инструкции для R928057041

POCKET COLORIMETER II

Бренд: Hach Страницы: 188

Бренд: WAGNER Страницы: 9

Бренд: PCB Piezotronics Страницы: 17

Бренд: Xtralis Страницы: 13

Бренд: Tektronix Страницы: 124

Бренд: OHAUS Страницы: 84

Бренд: Omega Страницы: 20

Бренд: Omega Страницы: 22

Бренд: Alma Страницы: 69

Бренд: Kawai Страницы: 28

Бренд: THORLABS Страницы: 63

Бренд: AL Страницы: 2

Бренд: HEIDENHAIN Страницы: 28

Бренд: YOKOGAWA Страницы: 12

Бренд: F&J Страницы: 33

IMI SENSORS 601A92

Бренд: PCB Piezotronics Страницы: 19

Бренд: Z-Wave Страницы: 6

Wind & Weather Medallion Series

Бренд: Downeaster Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды