Bosch R928057041 Скачать руководство пользователя | Manualshive

Страница: 14 / 46

background image

14/46 Operation

Bosch Rexroth AG

, RE 51550-B/09.2019

5 Operation

NOTICE

The device may not be operated outside its specifications!

5.1 WGM-D/WGM-R

This explanation of operation refers to options equipped with a display unit.

5.1.1 Switch-on procedure
When the device is connected to the supply voltage, it switches on immediately.
At the beginning, the software version appears briefly and the device checks the
installed components simultaneously. The display then changes to the measured
value display.
The function of the display and control unit is described below:

Fig. 2: Switch-on procedure

If an error message appears in the display during operation, please refer to the table
Troubleshooting in chapter "Service and Repair".

5.1.2 LED status displays
LEDs above the measured value display indicate the status of the switching outputs.
The LEDs are permanently assigned to the switching outputs.
The following table shows the factory settings for the assignment of the switching
outputs to filling level and temperature:

Table 2: Description of LED status displays

Figure

Description

2 switching outputs

LED 1 - yellow
Status switching output 1

Humidity

LED 2 - red
Status switching output 2

Temperature

The switching behavior of the LEDs (illuminated with closed or open switching
contact) can be changed.

dtet

dte

e

e

e

t

t

t

Operating

buttons

«
...
12
13
14
15
16
...
»

Содержание R928057041















































Отзывы:

Нет отзывов

Похожие инструкции для R928057041

Бренд: Labom Страницы: 5

Бренд: Hach Страницы: 145

Бренд: Hach Страницы: 358

Polymetron 9582sc

Бренд: Hach Страницы: 280

Бренд: HACH LANGE Страницы: 15

HYDROMETTE HB 30

Бренд: GANN Страницы: 65

Бренд: Magnescale Страницы: 2

Бренд: Datakom Страницы: 27

Бренд: Young Страницы: 5

SiteHawk SK-6000

Бренд: BIRD Страницы: 69

Бренд: OLYS Страницы: 2

CR-2010 PRO Series

Бренд: G-Tek Страницы: 48

Бренд: AccuEnergy Страницы: 23

Бренд: Haltech Страницы: 20

Бренд: F&F Страницы: 8

Бренд: Compact Instruments Страницы: 2

Бренд: Kawai Страницы: 2

Бренд: Dwyer Instruments Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды