MKE
10-4
Safety Guidelines for electrical drives
DOK-MOTOR*-MKE*******-PRJ1-EN-E1,44
•
06.97
DANGER
Dangerous movements!
Danger to life, severe injury or property damage!
⇒
The monitoring devices within the drive components
largely exclude malfunctions. This alone should not be
relied upon for personnel safety. Until the built-in
monitors are activated, it should be assumed that a
faulty drive motion can occur, the extent of which de-
pends on the nature of the problem and the oeprating
mode. Personnel protection is therefore dependent on
and must be secured with monitoring devices or mea-
sures that are superordinate in the machine. These
are instituted in the machine by the manufacturer after
a danger and error analysis has been complied with
which takes the afety measures for the machine into
consideration as well.
⇒
Personnel may not remain within the motional range
of the machine. Possible measures against accidental
accessing of personnel are:
- protective fences
- protective railings
- protective covers
- and photosensors.
⇒
Make sure that fencing and covers are strong enough
to absorb maximum motional energy.
⇒
E-stop switches must be easily accessible and in clo-
se proximity to the user. Check the E-stop prior to
commissioning to make sure it is operating properly.
⇒
Secure against unintentional startups of the drive via
the E-stop loop or use a starting lockout mechanism.
⇒
Prior to accessing or entering the danger zone, bring
the drives to a standstill.
⇒
Switch electrical equipment off via the main switch
and secure it against being switched back on in the
event of
- maintenance and service work
- when clearning
- prior to long operational breaks
⇒
The operation of high frequency, remote control and
radio equipment in the proximity of the machine’s
electronics and leads is to be avoided. If such must be
used, then check, prior to initial start, both system and
machine for possible malfunctions in all situations. It
may be necessary to run a special EMC check on the
machine.
Содержание R911274804
