manualshive.com logo in svg

Bosch Professional Series, Справочное руководство, Страница: 9 / 32

Поделиться
Скачать
Bosch Professional Series Скачать руководство пользователя страница 9

Professional Series TriTech AM Motion Detectors
with Anti-mask, LSN

Installation | en

9

Bosch Building Technologies

Reference Manual

2018.10 | 01 | F.01U.352.414

5

Installation

This section includes hardware details and the instructions you need to install the motion
detector base.

5.1

Self-locking cam

The detector includes a self-locking cam for easy installation. Refer to the following
information to open and close the detector.

Open the detector and remove the base

1.

Insert a flathead screwdriver into the self-locking cam hole.

2.

Turn to the unlock position.

3.

Slide, then lift the detector from the base.

1

2

3

Attach the detector back onto the base

Notice!

When you remove the detector from the base, the cam automatically returns to the locked
position. When you place the detector onto the base, the cam must remain in locked position.
Do not manually change the cam once you remove the detector from the base; doing so
unlocks the detector and prevents you from putting the detector correctly onto to base.

1.

Put detector onto the base.

2.

Slide the detector up until you hear it "click."

Содержание Professional Series

































Отзывы:

Нет отзывов