Bosch Professional Series Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 32

Bosch Professional Series Скачать руководство пользователя страница 5

Professional Series TriTech AM Motion Detectors
with Anti-mask, LSN

Introduction | en

5

Bosch Building Technologies

Reference Manual

2018.10 | 01 | F.01U.352.414

2

Introduction

This document provides install-related information for Professional Series LSN detectors.

2.1

About documentation

Copyright

This document is the intellectual property of Bosch Security Systems, Inc. and is protected by
copyright. All rights reserved.

Trademarks

All hardware and software product names used in this document are likely to be registered
trademarks and must be treated accordingly.

Notifications

This document uses Notices, Cautions, and Warnings to draw your attention to important
information.

Notice!

These include important notes for successful operation and programming of equipment, or
indicate a risk of damage to the equipment or environment.

!

Caution!

These indicate a hazardous situation which, if not avoided, could result in minor or moderate
injury.

!

Warning!

These indicate a hazardous situation which, if not avoided, could result in death or serious
injury.

2.2

Bosch Security Systems, Inc. product manufacturing dates

Use the serial number located on the product label and refer to the Bosch Security Systems,
Inc. website at http://www.boschsecurity.com/datecodes/.
The following image shows an example of a product label and highlights where to find the
manufacturing date within the serial number.

«
...
3
4
5
6
7
...
»

Содержание Professional Series

































Отзывы:

Нет отзывов