Bosch Professional Series Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 32

Bosch Professional Series Скачать руководство пользователя страница 11

Professional Series TriTech AM Motion Detectors
with Anti-mask, LSN

Installation | en

11

Bosch Building Technologies

Reference Manual

2018.10 | 01 | F.01U.352.414

Install on a bracket

Mounting brackets help align the detector to a vertical angle and to correct imperfections
(non-perpendicular angles) of installation surfaces.
Choosing a mounting bracket:
–

The B335 bracket allows a vertical pivot range of +10º to -20º and a horizontal pivot
range of ±25º.

–

The B328 bracket installs on a single-gang box and allows rotation of the detector. The
bracket allows you to insert the wiring through the black tube section in the center of the
bracket mounting plate and through the back of the detector base.

–

The B338 bracket designed for ceiling mounting allows a vertical pivot range of +7º to
-16º and a horizontal pivot of ±45º. The bracket allows you to insert the wiring through
the ceiling cavity and into the detector base.

When using a mounting bracket, pre-drill or tap out all of the mounting holes shown for that
bracket in the following figure.

«
...
9
10
11
12
13
...
»

Содержание Professional Series

































Отзывы:

Нет отзывов