Bosch Professional Series страница 14 Скачать руководство пользователя | Manualshive

Страница: 14 / 32

background image

14

en | Installation

Professional Series TriTech AM Motion Detectors

with Anti-mask, LSN

2018.10 | 01 | F.01U.352.414

Reference Manual

Bosch Building Technologies

5.4

Bubble level

The detector’s coverage pattern performs best when the detector is installed vertically and is
level both vertically and horizontally. The detector base includes a removable bubble level
which helps you align the unit. Use the bubble level to align the detector before drilling holes.

4

Put the detector base on the surface and install it in place using one screw only. Do not
over-tighten the screw.

4

Make sure the base is level from side to side.

4

Remove the bubble level and place it into the round cavity on the right side of the base.
Make sure the base is level and not tipped forwards or back.

4

Make adjustments until the base is level, and mark the remaining surface hole locations.

4

Remove the bubble level and place it back to its original position.

«
...
12
13
14
15
16
...
»

Содержание Professional Series

































Отзывы:

Нет отзывов

Похожие инструкции для Professional Series

Бренд: Omega Страницы: 8

Бренд: Nakayama Страницы: 36

Бренд: PAC Страницы: 2

AS-Interface AC1254

Бренд: IFM Страницы: 2

Бренд: Datamars Страницы: 144

Бренд: U-Line Страницы: 15

Бренд: OBO Bettermann Страницы: 2

Бренд: Mitox Страницы: 40

Бренд: FASTER TOOLS Страницы: 19

Бренд: CMT ORANGE TOOLS Страницы: 116

Бренд: H&H Страницы: 20

PowerPack T6600

Бренд: PNY Страницы: 2

Бренд: EASTMAN Страницы: 16

Бренд: Hilti Страницы: 191

Бренд: Rapid Страницы: 87

Бренд: Matatakitoyo Torque Tools Страницы: 2

Бренд: Neilsen Страницы: 16

LIFESTAR 20-1000TUL-DC

Бренд: Vanner Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды