Bosch NDN-921 Скачать руководство пользователя страница 74

Страница: 74 / 134

en |

Advanced Mode

FlexiDomeHD 720p IP Camera

AR18-10-B013 | v1.52 | 2011.06

Installation and Operation Manual

Bosch Security Systems

iSCSI Media

If an

iSCSI system

is selected as the storage medium, a

connection to the desired iSCSI system is needed to set the

configuration parameters.

The storage system selected must be available on the network

and completely set up. Amongst other things, it must have an IP

address and be divided into logical drives (LUN).

Enter the IP address of the required iSCSI destination in

the

iSCSI IP address

field.

If the iSCSI destination is password protected, enter this

into the

Password

field.

Click the

Read

button. The connection to the IP address is

established. The

Storage overview

field displays the

logical drives.

Local Media

The supported local recording media is displayed in the storage

overview field.

Activating and Configuring Storage Media

The storage overview displays the available storage media.

Select individual media or iSCSI drives and transfer these to the

Managed storage media

list. Activate the storage media in this

list and configure them for storage.

Note:

Each storage medium can only be associated with one user. If a

storage medium is already being used by another user,

decouple the user and connect the drive to the camera. Before

decoupling, make absolutely sure that the previous user no

longer needs the storage medium.

In the

Recording media

section, click the

iSCSI Media

Local Media

tab to display the applicable storage media in

the overview.

In the

Storage overview

section, double-click the required

storage medium, an iSCSI LUN or one of the other

Содержание NDN-921







































































































































Результаты поиска

Содержание NDN-921

Отзывы:

Похожие инструкции для NDN-921

Бренды по названию

Популярные бренды

Bosch NDN-921, Инструкция по установке и эксплуатации

Результаты поиска

Содержание NDN-921

Отзывы:

Похожие инструкции для NDN-921

Бренды по названию

Популярные бренды