Bosch NDN-921 Скачать руководство пользователя страница 69

Страница: 69 / 134

FlexiDomeHD 720p IP Camera

Advanced Mode

| en

Bosch Security Systems

Installation and Operation Manual

AR18-10-B013 | v1.52 | 2011.06

9.4.8

Encoder Streams

Select H.264 Settings

The codec algorithm for stream 1 is always:

–

H.264 MP 720p25/30 fixed

Select the codec algorithm for stream 2. The following are

available:

–

Copy Stream 1

–

H.264 BP+ bit-rate-limited

–

H.264 MP SD

Select the

Non-recording profile

for each stream from the

eight profiles that have been defined. This profile is used

when a stream is not used for recording. When a stream is

used for recording, the profile selected on the

Recording

Profiles

page is used.

Preview >>

Previews of streams 1 and 2 can be shown.

Click

Preview

to display a preview of the video for

streams 1 and 2. the current profile is shown above the

preview.

Click

1:1 Live View

below a preview to open a viewing

window for that stream. Various additional items of

information are shown across the top of the window.

Click

Preview <<

to close the preview displays.

Note:

Deactivate the display of the video images if the performance of

the computer is adversely affected by the decoding of the data

stream.

JPEG stream

Set the parmeters for the M-JPEG stream.

–

Select the

Max. frame rate

in images per second (IPS).

–

The

Picture quality

slider allows adjustment of the

M-JPEG image quality from

Low

High

Содержание NDN-921







































































































































Результаты поиска

Содержание NDN-921

Отзывы:

Похожие инструкции для NDN-921

Бренды по названию

Популярные бренды

Bosch NDN-921, Инструкция по установке и эксплуатации

Результаты поиска

Содержание NDN-921

Отзывы:

Похожие инструкции для NDN-921

Бренды по названию

Популярные бренды