Bosch NDN-921 Скачать руководство пользователя страница 73

Страница: 73 / 134

FlexiDomeHD 720p IP Camera

Advanced Mode

| en

Bosch Security Systems

Installation and Operation Manual

AR18-10-B013 | v1.52 | 2011.06

9.5

Recording

Record the images from the camera to local storage media or to

an appropriately configured iSCSI system. For long-term

authoritative images use an appropriately sized iSCSI system.

MicroSDHC cards are the ideal solution for shorter storage

times and temporary recordings, for example, local buffering in

the event of network interruptions.

A Video Recording Manager (

VRM

) can control all recording

when accessing an iSCSI system. The VRM is an external

program for configuring recording tasks for video servers. For

further information, contact your local customer service at

Bosch Security Systems.

9.5.1

Storage Management

Device manager

If the

VRM

option is activated, the VRM Video Recording

Manager manages all recording and no further settings can be

configured here.

Note:

Activating or deactivating VRM causes the current settings to be

lost; they can only be restored through reconfiguration.

Recording media

Select the required recording media to activate them and then

configure the recording parameters.

Recording

Storage Management

Recording Profiles

Retention Time

Recording Scheduler

Recording Status

Содержание NDN-921







































































































































Результаты поиска

Содержание NDN-921

Отзывы:

Похожие инструкции для NDN-921

Бренды по названию

Популярные бренды

Bosch NDN-921, Инструкция по установке и эксплуатации

Результаты поиска

Содержание NDN-921

Отзывы:

Похожие инструкции для NDN-921

Бренды по названию

Популярные бренды