background image

30

en | Camera

AUTODOME IP starlight 7000i

2020-07 | v0.7 |

User Manual

Bosch Security Systems

I/P-frame delta QP

This parameter sets the ratio of the I-frame quantization (QP) to the P-frame quantization
(QP). For example, you can set a lower value for I-frames by moving the slide control to a
negative value. Thus, the quality of the I-frames relative to the P-frames is improved. The total
data load will increase, but only by the portion of I-frames. The basic setting Auto
automatically adjusts to the optimum combination of movement and image definition (focus).
To obtain the highest quality at the lowest bandwidth, even in the case of increased
movement in the picture, configure the quality settings as follows:
1.

Observe the coverage area during normal movement in the preview images.

2.

Set the value for 

Min. P-frame QP

 to the highest value at which the image quality still

meets your needs.

3.

Set the value for 

I/P-frame delta QP

 to the lowest possible value. This is how to save

bandwidth and memory in normal scenes. The image quality is retained even in the case
of increased movement since the bandwidth is then filled up to the value that is entered
under 

Maximum bit rate

.

Background delta QP

Select the appropriate encoding quality level for a background region defined in Encoder
Regions. The lower the QP value, the higher the encoding quality.

Object delta QP

Select the appropriate encoding quality level for an object region defined in Encoder Regions.
The lower the QP value, the higher the encoding quality.

Default

Click 

Default

 to return the profile to the factory default values.

5.4

Encoder Streams

Note: If you access this menu while the camera is recording, the following message appears at
the top of the page:
Recording is currently active. Therefore, for ‘Current profile’ the respective stream profile
selected for recording is displayed for information.

Stream prioritization

Select the stream that should not drop any frame.
For each stream, select the appropriate options in the fields that follow.

Coding standard

Select the coding standard (H.264 or H.265) for the stream.

VCA overlays

Select the video stream into which to embed VCA overlays.

Non-recording profile

Select one of the following profiles for each stream:

Profile number

Default Profile name

Description

Profile 1

HD Image Optimized

For an HD image, the video bit rate and frame
quality are adjusted to ensure that the picture
quality is the priority.

Profile 2

HD Balanced

For an HD image, the video bit rate and frame
quality are adjusted to a median profile for
everyday use.

Содержание MIC IP starlight 7000i























































































Отзывы: