Bosch MIC IP starlight 7000i Скачать руководство пользователя страница 24

Страница: 24 / 86

en | Camera

AUTODOME IP starlight 7000i

2020-07 | v0.7 |

User Manual

Bosch Security Systems

Restore mode defaults

Click

Restore Mode Defaults

to restore the factory default modes. Confirm you decision.

5.2.1

Picture Settings

Color

White Balance

Adjusts the color settings to maintain the quality of the white areas of the image.
–

ATW

: allows the camera to adjust color reproduction continuously.

–

Indoor

: white balance tracking for indoor use.

–

Outdoor

: white balance tracking for outdoor use.

–

AWB hold

: places the ATW on hold and saves the color settings.

–

Extended ATW

(default): allows the camera to adjust constantly for optimal color

reproduction.

–

Manual

: Red and Blue gain can be set manually to a desired position.

Red Gain

The red gain adjustment offsets the factory white point alignment (reducing red introduces
more cyan).

Blue Gain

The blue gain adjustment offsets the factory white point alignment (reducing blue introduces
more yellow). It is only necessary to change the white point offset for special scene
conditions.
Note: The fields

Sodium red level

and

Sodium blue level

appear only when the value in the

field

White balance

is “Sodium lamp auto” or “Sodium lamp.”

Saturation

Select the percentage of light or color in the video image. The range of options is from 60% to
200%; the default is 100%.

Color hue

Select the degree of color in the video image. The range of options is from -14° to 14°; the
default is 0°.

Exposure and gain control

Gain control

Adjusts the automatic gain control (AGC).
–

AGC

(default): Automatically adjusts the gain to the lowest possible value needed to

maintain a good picture.

–

Fixed

: no enhancement. This setting disables the Max. Gain Level option.

Fixed Gain

Use the slide to select the desired number for fixed gain. The default is 2.

Maximum gain level

To set the

Maximum gain level

, select

Low

Medium

High

from the drop-down box.

AE-response speed

Select the speed of the response of auto exposure. Options are Super slow, Slow, Medium
(default), Fast.

Shutter Mode

–

Fixed

: The shutter mode is fixed to a selectable shutter speed.

–

Automatic exposure

: increases camera sensitivity by increasing the integration time on

the camera. This is accomplished by integrating the signal from a number of consecutive
video frames to reduce signal noise.

Содержание MIC IP starlight 7000i























































































Результаты поиска

Содержание MIC IP starlight 7000i

Отзывы:

Похожие инструкции для MIC IP starlight 7000i

Бренды по названию

Популярные бренды

Bosch MIC IP starlight 7000i, Руководство пользователя

Результаты поиска

Содержание MIC IP starlight 7000i

Отзывы:

Похожие инструкции для MIC IP starlight 7000i

Бренды по названию

Популярные бренды