User Manual | Mitchell Diagnostics | Scan Tool | 45 | en
©Mitchell International, Inc.
581624 | REV. B | 06.2017 | APDMD032018
Automated System Test Report
2007 Jeep Wrangler Unlimited X 3.8L
Menu
SUMMARY
DTCs
DATA STREAM SNAPSHOT
MODE 1
FREEZE FRAME
MODE 5
MODE 6
Share
Clear
Refresh
Save
Mode 2 Freeze Frames
Evaporative Emissions
System Vapor Pressure
16.06
inH2O
Catalyst Temperature
Bank 1 Sensor 1
Catalyst Temperature
Bank 2 Sensor 1
Catalyst Temperature
Bank 1 Sensor 2
Distance MIL Active
13026
miles
3881
miles
Distance Since DTC Clear
ss02789
Mode 2 displays recorded data in the form of a DS
snapshot by the vehicle’s computer when specific
DTC are set and the MIL is illuminated.
Mode 5 (Oxygen sensor tests)
Mode 5 views O2 sensor monitor test results.
Automated System Test Report
2007 Jeep Wrangler Unlimited X 3.8L
Menu
SUMMARY
DTCs
DATA STREAM SNAPSHOT
MODE 1
FREEZE FRAME
MODE 5
MODE 6
Share
Clear
Refresh
Save
Oxygen Sensor Tests (Mode 5)
Bank 1 Sensor 1
Maximum Sensor Voltage For Test Cycle
Description
Min
Value
Max
Units
0.000
0.003
1.275
V
Lean To Rich Sensor Threshold Voltage
0.000
0.003
1.275
V
High Sensor Voltage For Switch Time
Calculation
0.000
0.003
1.275
V
Minimum Sensor Voltage For Test Cycle
0.000
0.003
1.275
V
ss02790
Mode 5 views O2 sensor monitor test results. Mode
5 displays the average of the O2 sensor monitor
test results measured over a period of time. The
parameters of this measurement vary between
manufacturers. It may be necessary to run the
vehicle for a period of time to allow the O2 sensors
to fully warm up and begin operating.
Note: Mode 5 is not supported on all vehicles.
Mode 6 (Non-continuous monitor tests)
Mode 6 views onboard monitoring test results for
noncontinuous monitor systems.
Automated System Test Report
2007 Jeep Wrangler Unlimited X 3.8L
Menu
SUMMARY
DTCs
DATA STREAM SNAPSHOT
MODE 1
FREEZE FRAME
MODE 5
MODE 6
Share
Clear
Refresh
Save
Non-Continuously Monitored Tests
(Mode 6)
ECU: ENGINE
N/A
MIN
9667
VALUE
25292
MAX
N/A
UNITS
Failed
Passed
TID 1
TID 1
CID 1
TID 1
TID 2
TID 2
CID 2
TID 2
ss02791
Non-Continuous Monitor Tests (Mode 6) are pass/
fail tests, including certain EVAP tests, catalyst, and
EGR. The following information is reported:
• ECU.
• TID (test identification) indicates the system
monitor.
• CID (component identification) indicates the
component tested and its test value.
• Minimum value, maximum value, and current
value for each non-continuous monitor.
• Pass or fail test result.
Each vehicle manufacturer assigns a code number
to their system monitors and components. Refer
to the vehicle manufacturers Mode 6 code chart to
determine the failure indicated by the TID and CID. If
this chart is not readily available, run an automated
system test (AST) from the DTC screen and select
Mode 6. See Read DTCs section for more information
regarding steps to complete this action. This may
provide a more detailed description of the Mode 6
test information.
Automated System Test (AST) Button
Definitions
Refresh DTCs Button
Tapping the Refresh button initiates a
fresh scan of DTCs from the vehicle.
Share DTCs Button
Tapping the Share button opens the
app and initiates options. Depending on
what’s available at the time. Share a list
containing all the DTCs set by email or
Bluetooth or USB.
