manualshive.com logo in svg

Bosch IdealShield POWER XPRESS, Инструкция по установке, Страница: 4 / 27

Поделиться
Скачать
Bosch IdealShield POWER XPRESS Скачать руководство пользователя страница 4

CONTACT US FOR A QUOTE TODAY

1-800-731-1722

WWW.IDEALSHIELD.COM

4

Power Xpress™ Dual Bollard Charge Station 

Installation Guide

576414 Rev. A

INSTALLATION SAFETY

SAVE THESE IMPORTANT SAFETY INSTRUCTIONS.

This guide contains important instructions that must be followed during the installation of the electric ve-

hicle supply equipment (EVSE). All instructions should be carefully read before installation of the EVSE.

 WARNING: Turn OFF the circuit breaker 

at the service or distribution panel before 

performing any electrical work or repairs.

 WARNING: The EVSE should be installed by 

a licensed electrician in accordance with all 

local electrical codes, ordinances, and all 

authorities having jurisdiction.

 WARNING: Do not install the EVSE near 

flammable,  explosive,  or  combustible 

materials. Do not locate or store flammable, 

explosive, or combustible materials near the 

EVSE. 

 WARNING: Improper installation of the 

EVSE can result in personal injury or 

product damage.

 WARNING: This EVSE installation guide 

is not a substitute for electrical safety 

precautions.

 WARNING: Use this EVSE within the 

specified  operating  parameters.  Failure  to 

do so may result in injury or death.

 WARNING: Locate and install this EVSE in 

a location where the charge cable will not 

be stepped on, tripped over, or subject to 

damage or stress.

 WARNING: The EVSE must be connected to a 

grounded, metal, permanent wiring system, 

or an equipment-grounding conductor 

must be run with the circuit conductors 

and connected to the equipment grounding 

terminal on the EVSE.

  CAUTION: Incorrect installation of the EVSE 

can  result  in  damage  to  the  vehicle’s  battery 

and to the EVSE itself. These damages will void 

the warranty for the vehicle and the EVSE.

  CAUTION: 

Do not operate the EVSE in 

temperatures beyond its operating range of 

-40°F to +122°F (-40°C to +50°C).

Содержание IdealShield POWER XPRESS




























Отзывы:

Нет отзывов