Bosch IdealShield POWER XPRESS Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 27

Bosch IdealShield POWER XPRESS Скачать руководство пользователя страница 25

CONTACT US FOR A QUOTE TODAY

1-800-731-1722

WWW.IDEALSHIELD.COM

25

Power Xpress™ Dual Bollard Charge Station

Installation Guide

576414 Rev. A

TROUBLESHOOTING

If there is a charging issue proceed with the following steps. If the issue persists after three attempts

call Bosch at 1-877-805-EVSE (3873) for assistance.

Problem Indicated by LED Status Solution

Pilot charging error

1.

Verify supply-side power. The green POWER LED should be on.

If green POWER LED is off, locate load center/panel and reset

breaker.

2.

Press the master clear RESET button on the front panel of the

EVSE to attempt a charge-restart.

3. If the red STATUS LED remains on, disconnect the EVSE coupler

from the vehicle charge port, wait 10 seconds, and reconnect
the coupler.

Ground fault detected

1.  Disconnect main service power at service panel.
2.  Disconnect the EVSE coupler from the vehicle.
3.  Inspect the EVSE connector and the vehicle charge port verifying

both are clean and undamaged. If vehicle charge port needs

cleaning, follow manufacturer instructions for cleaning. Clean
EVSE connector with a dry or damp cloth if necessary.

4. Restore main service power.
5. Reconnect the coupler to the vehicle port.

Ground monitor interrupted

1.  Disconnect main service power at service panel.
2.  Disconnect the EVSE coupler from the vehicle.
3.  Inspect the EVSE connector and the vehicle charge port verifying

both are clean and undamaged. If vehicle charge port needs

cleaning, follow manufacturer instructions for cleaning. Clean
EVSE connector with a dry or damp cloth if necessary.

4. Restore main service power.
5. Reconnect the coupler to the vehicle port.

Operation fault

1.

Verify supply-side power. The green POWER LED should be on.

If green POWER LED is off, locate load center/panel and reset

breaker.

2.

Press the master clear RESET button on the front panel of the

EVSE to attempt a charge-restart.

3. If the red STATUS LED remains on, disconnect the EVSE coupler

from the vehicle charge port, wait 10 seconds, and reconnect
the coupler.

«
...
23
24
25
26
27
»

Содержание IdealShield POWER XPRESS




























Отзывы:

Нет отзывов