English |
11
Bosch Power Tools
1 609 92A 1RV | (3.11.15)
Rubber Sanding Plate
For operations with the rubber sanding plate 14, al-
ways mount the hand guard 13.
See graphics page for the mounting sequence.
Screw on the round nut
16
and tighten with the two-pin spanner.
Cup Brush/Disc Brush
For operations with the cup brush/wheel brush, always
mount the hand guard 13.
See graphics page for the mounting sequence.
The cup brush/disc brush must be able to be screwed onto
the grinder spindle until it rests firmly against the grinder
spindle flange at the end of the grinder spindle threads. Tight-
en the cup brush/disc brush with an open-end spanner.
Approved Grinding Tools
All grinding tools mentioned in these operating instructions
can be used.
The permissible speed [min
-1
] or the circumferential speed
[m/s] of the grinding tools used must at least match the values
given in the table.
Therefore, observe the permissible
rotational/circumferen-
tial speed
on the label of the grinding tool.
Rotating the Machine Head
Before any work on the machine itself, pull the mains
plug.
The machine head can be
rotated with respect to
the machine housing in
90° steps. In this man-
ner, the On/Off switch
can be brought into a
more convenient posi-
tion for special working
situations, e.g. for left-
handed persons.
Completely unscrew the
four screws. Rotate the
machine head carefully,
without removing it from the hous-
ing,
to the new position. Screw in and tighten the four screws
again.
Dust/Chip Extraction
Dust from materials such as lead-containing coatings,
some wood types, minerals and metal can be harmful to
one’s health. Touching or breathing-in the dust can cause
allergic reactions and/or lead to respiratory infections of
the user or bystanders.
Certain dust, such as oak or beech dust, is considered car-
cinogenic, especially in connection with wood-treatment
additives (chromate, wood preservative). Materials con-
taining asbestos may only be worked by specialists.
– As far as possible, use a dust extraction system suitable
for the material.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the
materials to be worked.
Prevent dust accumulation at the workplace.
Dust can
easily ignite.
Operation
Starting Operation
Observe correct mains voltage! The voltage of the pow-
er source must agree with the voltage specified on the
nameplate of the machine. Power tools marked with
230 V can also be operated with 220 V.
Hold power tool by insulated gripping surfaces 20 and
auxiliary handle 3 only. The accessory may contact hid-
den wiring or its own cord.
Accessory contacting a “live”
wire may make exposed metal parts of the power tool “live”
and shock the operator.
When operating the machine with power from mobile genera-
tors that do not have sufficient reserve capacity or are not
equipped with suitable voltage control with starting current
amplification, loss of performance or untypical behavior can
occur upon switching on.
Please observe the suitability of the power generator being
used, particularly with regard to the mains voltage and fre-
quency.
Switching On and Off
To
start
the power tool, push the On/Off switch
2
forwards.
To
lock
the On/Off switch
2
, press the On/Off switch
2
down
at the front until it latches.
To
switch off
the power tool, release the On/Off switch
2
or,
if it is locked, briefly push down the back of the On/Off switch
2
and then release it.
Check grinding tools before using. The grinding tool
must be mounted properly and be able to move freely.
Carry out a test run for at least one minute with no load.
Do not use damaged, out-of-centre or vibrating grind-
ing tools.
Damaged grinding tools can burst and cause in-
juries.
To save energy, only switch the power tool on when using it.
max.
[mm]
[mm]
D
b
d
[min
-1
]
[m/s]
115
125
6
6
22.2
22.2
12000
12000
80
80
115
125
–
–
12000
12000
80
80
75
30
M 14
12000
80
b
d
D
D
D
b
d
OBJ_BUCH-2485-002.book Page 11 Tuesday, November 3, 2015 3:16 PM
