English |
11
Bosch Power Tools
1 609 92A 0NT | (23.5.14)
10
Upper cutter
11
Bottom cutter
12
Adjustment screw, bottom cutter
13
Fastening screw for bottom cutter
14
Setting gauge*
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.
Technical Data
Noise/Vibration Information
Sound emission values determined according to EN 60745.
Typically the A-weighted sound pressure level of the product
is less than 70 dB(A). Uncertainty K < 1.5 dB.
The noise level when working can exceed 80 dB(A).
Wear hearing protection!
Vibration total values a
h
(triax vector sum) and uncertainty K
determined according to EN 60745:
a
h
= 3.5 m/s
2
, K< 1.5 m/s
2
.
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This
may significantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may signif-
icantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under “Technical Data” is in conformity with all rele-
vant provisions of the directives 2011/65/EU, 2014/30/EU,
2006/42/EC including their amendments and complies with
the following standards: EN 60745-1, EN 60745-2-8.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
70764 Leinfelden-Echterdingen, GERMANY
Robert Bosch GmbH, Power Tools Division
70764 Leinfelden-Echterdingen, GERMANY
Leinfelden, 28.04.2014
Assembly
Battery Charging
Use only the chargers listed in the technical data.
Only
these chargers are matched to the lithium-ion battery of
your power tool.
Note:
The battery supplied is partially charged. To ensure full
capacity of the battery, completely charge the battery in the
battery charger before using your power tool for the first time.
The lithium-ion battery can be charged at any time without re-
ducing its service life. Interrupting the charging procedure
does not damage the battery.
Battery Charge-control Indication
The three green LEDs of the battery charge-control indicator
4
indicate the charge condition of the battery
2
. For safety
reasons, it is only possible to check the status of the charge
condition when the machine is at a standstill.
– To indicate the charge condition, press and hold button
3
of the switched off machine.
Removing the battery
– To remove the battery
2
, press the unlocking buttons
1
and pull the battery out of the machine to the rear.
Do not
exert any force.
Operation
Starting Operation
Inserting the battery
Use only original Bosch lithium-ion batteries with the
voltage listed on the nameplate of your power tool.
Using
other batteries can lead to injuries and pose a fire hazard.
Cordless Sheet Metal Shear
GSC 10,8 V-LI
Article number
3 601 J26 1..
Rated voltage
V=
10.8
Stroke rate at no load n
0
min
-1
3600
Max. steel sheet cutting capacity
#
mm
1.3
Smallest curve radius
mm
15
Weight according to
EPTA-Procedure 01/2003
kg
1.4
Permitted ambient temperature
– during charging
– during operation* and during
storage
°C
°C
0...+45
–20...+50
Recommended batteries
GBA 10,8V...
Recommended chargers
AL 11..
#
to 400 N/mm
2
with reference to steel sheet
* Limited performance at temperatures <0 °C
Henk Becker
Executive Vice President
Engineering
Helmut Heinzelmann
Head of Product Certification
PT/ETM9
LED
Capacity
Continuous lighting 3 x green
2/3
Continuous lighting 2 x green
1/3
Continuous lighting 1 x green
<1/3
Flashing light 1 x green
Reserve
OBJ_BUCH-840-006.book Page 11 Friday, May 23, 2014 12:04 PM
