Bosch DIVAR DIP-7080-00N Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 72

background image

–

Reset: The reset button is used to reboot the system.

–

Power: The main power switch is used to apply or remove power from the power

supply to the server system. Turning off system power with this button removes the main
power but keeps standby power supplied to the system. Therefore, you must unplug
system before servicing.

Control panel LEDs

The control panel located on the front of the chassis has five LEDs. These LEDs provide you
with critical information related to different parts of the system. This section explains what
each LED indicates and any corrective action you may need to take.

–

Power failure: A flashing LED indicates a power failure in the power supply.

–

Overheat/fan fail: A flashing LED indicates a fan failure.

When continuously on (not flashing) the LED indicates an overheat condition, which may
be caused by cables obstructing the airflow in the system or the ambient room
temperature being too warm. Check the routing of the cables and make sure all fans are
present and operating normally. You should also check to make sure that the chassis
covers are installed. Finally, verify that the heat sinks are installed properly.
This LED will remain flashing or on as long as the fan failure/overheat condition exists.

–

NiC2: A flashing LED indicates network activity on GLAN2.

–

NIC1: A flashing LED indicates network activity on GLAN1.

–

HDD: A flashing LED indicates IDE channel activity in the SAS/SATA drive, SCSI

drive, and/or DVD-ROM drive activity.

–

Power: Indicates power is being supplied to the system's power supply units.

This LED should normally be illuminated when the system is operating.

Drive carrier LEDs

Your chassis uses SAS/SATA.
SAS/SATA drives
Each SAS/SATA drive carrier has two LEDs.

2.3.2

2.3.3

12

en | System overview

DIVAR IP 7000 2U

2013.09 | V2 | DOC

Installation Manual

Bosch Sicherheitssysteme GmbH

«
...
10
11
12
13
14
...
»

Содержание DIVAR DIP-7080-00N









































































Отзывы:

Нет отзывов

Похожие инструкции для DIVAR DIP-7080-00N

Бренд: Linksys Страницы: 2

Бренд: Abocom Страницы: 1

SAFETank Series

Бренд: Raidon Страницы: 49

Бренд: TC Electronic Страницы: 174

Finalizer Express

Бренд: TC Electronic Страницы: 33

Бренд: Gate Страницы: 8

Бренд: N.A.T. Страницы: 32

DesignCore RVP-TDA3 Series

Бренд: D3 Страницы: 34

Бренд: Ubiquiti Страницы: 20

Бренд: AMG Systems Страницы: 2

Бренд: Datasat Страницы: 24

Fan Tray 8820-S2-900

Бренд: Paradyne Страницы: 6

Бренд: Xmart Страницы: 8

LBON320AC Series

Бренд: Lindsay Broadband Страницы: 4

Бренд: Variscite Страницы: 18

Бренд: UfiSpace Страницы: 32

Бренд: Z Microsystems Страницы: 51

Enterasys Matrix 2G4082-25

Бренд: Enterasys Страницы: 58

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды