Bosch DIP-71F0-00N Скачать руководство пользователя страница 17

Страница: 17 / 56

DIVAR IP 7000 (3U)

System overview | en

Bosch Sicherheitssysteme GmbH

Installation Manual

2016.08 | V2.1 | DOC

This LED will remain flashing or on as long as the fan failure/overheat condition exists.

–

NiC2

: A flashing LED indicates network activity on GLAN2.

–

NIC1

: A flashing LED indicates network activity on GLAN1.

–

HDD

: A flashing LED indicates IDE channel activity in the SAS/SATA drive, SCSI

drive, and/or DVD-ROM drive activity.

–

Power

: Indicates power is being supplied to the system's power supply units.

This LED should normally be illuminated when the system is operating.

3.3.3

Drive carrier LEDs

LED color

Blinking pattern

Behavior for device

ActivityLED

Blue

Solid On

SAS drive installed

Blue

Blinking

I/O activity

StatusLED

Red

Solid On

Failed drive for SATA/NVMe with
RSTe support

Red

Blinking at 1 Hz

Rebuild drive for SATA with RSTe
support

Red

Blinking with two
blinks and one stop
at 1 Hz

Hot spare for SATA with RSTe
support

Red

On for five seconds,
then off

Power on for SATA with RSTe
support

Red

Blinking at 4 Hz

Identify drive for SATA with RSTe
support

3.3.4

Power supply LEDs

On the rear of the power supply module, an LED displays the status.
–

Solid Green:

When illuminated, indicates that the power supply is on.

–

Solid Amber:

When illuminated, indicates the power supply is plugged in and turned off,

or the system is off but in an abnormal state.

–

Blinking Amber:

When blinking, the system power supply temperature has reached 63”C.

The system will automatically turn off when the power supply temperature reaches 70”C
and restart when the power supply temperature goes below 60”C.

Содержание DIP-71F0-00N

























































Результаты поиска

Содержание DIP-71F0-00N

Отзывы:

Похожие инструкции для DIP-71F0-00N

Бренды по названию

Популярные бренды

Bosch DIP-71F0-00N, Руководство по установке

Результаты поиска

Содержание DIP-71F0-00N

Отзывы:

Похожие инструкции для DIP-71F0-00N

Бренды по названию

Популярные бренды