Bosch Condens 2000F16 Regular boiler Скачать руководство пользователя | Manualshive

Страница: 39 / 62

background image

Servicing and spares

|

39

6 720 ... ... (YYYY/MM)

Product Name

– CO

2

is less than 0.2%

▶ If the readings are outside these limits then this indicates that there

is a problem with the flue system or combustion circuit, e.g. missing
or dislodged seals

Fig. 51 Flue integrity test

10.4

Service inspection - Component access

Remove the boiler front panel to gain access to components.
▶ Pull the top corners of the front panel away from the case until the

ball catches are released.

▶ Lift the panel off the two lower brackets and set the panel aside.
▶ Lower the control panel into the service position.
▶ Remove the four screws securing the combustion chamber cover and

remove to gain access to the components.

Fig. 52 Component access

10.4.1 Control panel - Service position

To lower the control panel into the service position, remove one top
screw [1] from each side of the mounting bracket, loosen the bottom
screws slightly and pivot the panel forward. The control panel is
supported at approximately 100 °.

Fig. 53 Control panel to the service position

10.5 CHECKING THE GAS INLET PRESSURE

▶ Refer to section 7.5 and check that the gas working pressures in the

system conform to within the figures shown below:

6720809859-23.1Wo

NOTICE:

Gas inlet pressure

▶ Ensure that the gas pressure is satisfactory with all

other gas appliances working.

▶ Do not continue with the other checks if the correct

gas pressure can not be achieved.

6720809859-18.1Wo

1

6720809859-19.1W

o

«
...
37
38
39
40
41
...
»

Содержание Condens 2000F16 Regular boiler































































Отзывы:

Нет отзывов

Похожие инструкции для Condens 2000F16 Regular boiler

Бренд: saro Страницы: 15

ASPIRO A 29 R/SA

Бренд: Arca Caldaie Страницы: 38

Бренд: Toastmaster Страницы: 13

Бренд: Laars Страницы: 138

Бренд: Lochinvar Страницы: 72

Бренд: U.S. Boiler Company Страницы: 176

Бренд: Fondital Страницы: 80

Planet Super 4 WM

Бренд: Sime Страницы: 36

ECO COMPACT 200

Бренд: Pleion Страницы: 11

Бренд: Raypak Страницы: 6

Бренд: Ravelli Страницы: 200

Бренд: Westinghouse Страницы: 94

Prestige PARKIT101

Бренд: TriangleTube Страницы: 6

Бренд: CR Remeha Страницы: 72

Netaheat Electronic 10/16

Бренд: Potterton Страницы: 24

Mexico Super CF4120

Бренд: Ideal Boilers Страницы: 36

Бренд: ACV Страницы: 42

Performa System 12e

Бренд: Potterton Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды