Bosch CFB 840 Скачать руководство пользователя страница 12

Страница: 12 / 56

Commissioning

CFB 840

6 720 802 836 (2012/05)

Heating circuit function

Positions

and

Manual

are special settings of the manual switch for the

heating circuit (

fig. 12, page [6]) reserved to contractors.

Commissioning

6.1

Commissioning the programming unit

The programming unit can be used with all control units of the series 7xx,

8xx and 9xx.
The programming unit can be used as follows:

•

directly in the control unit

•

wall-mounted as remote control unit or

•

in an adapter with separate power source.

The Programmer starts the initialisation process as soon as supply

voltage is connected. The display shows

MEC is initialised

The control unit address is then briefly displayed.
The display shows

Connection with ctrl. unit Address xx

established.

Depending on the individual application, the display shows various

information:

6.1.1 New Programmer installed in a control unit

If a brand new Programmer has been installed in the control unit and the

connections with the control unit have been established, data are

immediately downloaded from the control unit.
The display shows

Monitor data will from ctrl unit taken

6.1.2 Programmer is installed in another control unit

If the Programmer is programmed with a software version that is not able

to recognise this type of control unit, the display shows

Unknown

control unit

Remove the Programmer from the control unit and replace by a

Programmer with a suitable software version.

6.1.3 Programmer with set parameters installed in control unit

After the Programmer has been installed in the control unit, the two

adjacent displays will initially be re-displayed.

MEC is initialised

Connection with ctrl. unit Address xx established

Alternative control unit type

Initially, only data from the control unit can be downloaded, if the type of

control unit varies from that entered in the programming unit. The

display shows

Other Ctrl. unit type, Night button receive

Press the

Night mode

button.

The display shows

Data are from ctrl unit taken

Alternative control unit of the same type

If the Programmer is connected to a different control unit of the same

type, the display will show the below message for approx. 3 seconds.

NB other control unit

If the Programmer programming unit is separated from the control unit

and data is modified, the display shows

Aut button transmit, Night

button receive

, when the unit is reinstalled into a control unit of the

same type. The control unit scans whether the new data should be

accepted or whether the old data from the control unit should be used

again.
To adopt the new data:

Press

AUT

The display shows

Data are to ctrl unit

sent

To adopt the data from the control unit:

Press the

Night mode

button.

The display shows

Data are from ctrl unit taken

Identical control unit

If the programming unit is separated from the control unit and data is

modified externally, the display shows

Aut button transmit, Night

button receive

, when the unit is reinstalled into a control unit of the

same type. The control unit scans whether the new data should be

accepted or whether the old data from the control unit should be used

again.
To adopt the new data:

Press

AUT

The display shows

Data are to ctrl unit

sent

To adopt the data from the control unit:

Press the

Night mode

button.

The display shows

Data are from ctrl unit taken

In normal operation the manual switch should be in the

AUT

position.

Current functions are indicated by LEDs.

Position

Function

The heating circuit pump is switched on. The

mixing valve is switched volt-free and can be

manually operated.
The central heating or the DHW circuit

operates in automatic mode.

The heating circuit pump is switched off. The

mixing valve is switched volt-free. The control

functions remain active.

Table 10 Heating circuit functions FM442/CMM 920

If the Programmer is fitted in the control unit or wall

mounting plate, it automatically detects the control unit

to which it is connected (automatic detection). You do

not have to select the control unit.

Содержание CFB 840

























































Результаты поиска

Содержание CFB 840

Отзывы:

Похожие инструкции для CFB 840

Бренды по названию

Популярные бренды

Bosch CFB 840, Инструкции по обслуживанию

Результаты поиска

Содержание CFB 840

Отзывы:

Похожие инструкции для CFB 840

Бренды по названию

Популярные бренды