Bosch CFB 840 Скачать руководство пользователя страница 19

Страница: 19 / 56

General specification data

6 720 802 836 (2012/05)

CFB 840

8.4

Remote adjust

The remote adjustment offers the option of external data entry and

adjustment via a remote system.

Call up the service level.

GENERAL PARAM.

appears as the first main menu.

Press

Display

to call up a submenu.

Turn the rotary dial until submenu

Remote adjust.

is displayed.

Hold down button

Display

and turn the rotary dial until the required

value is shown.

The display shows the set value.

Release

Display

to save your input.

Press

Back

to return to the next higher level.

8.5

Manual fault message control

A fault message can be shown in the display of the programming unit

when the manual switch of the function module is set to

Manual

Call up the service level.

GENERAL PARAM.

appears as the first main menu.

Press

Display

to call up a submenu.

Turn the rotary dial until submenu

Fault message manual control

displayed.

Hold down button

Display

and turn the rotary dial until the required

value is shown.

The display shows the set value.

Fig. 22 Manual fault message control

Release

Display

to save your input.

Press

Back

to return to the next higher level.

8.6

Automatic maint. message

At the user level an automatic maintenance message to appear on the

programming unit display can be generated.
The following settings are possible:

•

Maintenance message by date. Entry of the date of the next service

date (01.01.2000 – 31.12.2088).

•

Maintenance after hours run (only for control units with direct boiler

control).

Call up the service level.

GENERAL PARAM.

appears as the first main menu.

Press

Display

to call up a submenu.

Turn the rotary dial until submenu

automatic maint. message

displayed.

Hold down button

Display

and turn the rotary dial until the required

value is shown.

The display shows the set value.

Fig. 23 Automatic maint. message

Release

Display

to save your input.

Turn the rotary dial one increment clockwise.

Setting

options

Explanation

yes

Optional remote adjustment via the telecontrol system

Remote adjustment is not possible, but system data

can be downloaded and monitored.

Table 17 Setting options Remote adjustment

This parameter cannot be adjusted via the telecontrol

system; it is only intended to be changed in situ.

Input range

Factory setting

Remote adjust.

yes

Table 18 Setting range Remote adjustment

GENERAL PARAM.
Fault message
manual control

Fault message

6 720 802 836-23.1TL

is shown, a warning notice appears if the flap is

closed.

Fault message

is shown, an entry also appears in the

fault log. Automatic forwarding via the CFB 840

telecontrol system is then possible.

cent. fault mess

is shown, the output of a central fault

message also appears via a volt free contact e.g. via the

FM448/CMB 900-0-10V function module.

Input range

Factory setting

Fault message

manual control

Fault message

central fault message

Table 19 Setting range Manual switch fault message

The maintenance message "after hours run" is not

possible with this control unit.

GENERAL PARAM.
automatic
maint. message

Date

6 720 802 836-24.1TL

Содержание CFB 840

























































Результаты поиска

Содержание CFB 840

Отзывы:

Похожие инструкции для CFB 840

Бренды по названию

Популярные бренды

Bosch CFB 840, Инструкции по обслуживанию

Результаты поиска

Содержание CFB 840

Отзывы:

Похожие инструкции для CFB 840

Бренды по названию

Популярные бренды