Bosch CFB 840 Скачать руководство пользователя страница 30

Страница: 30 / 56

Heating circuit data

CFB 840

6 720 802 836 (2012/05)

Call up the service level.

GENERAL PARAM.

appears as the first main menu.

Turn the rotary dial until main menu

Heat.circuit

+ No. is displayed.

Press

Display

to call up a submenu.

Turn the rotary dial until submenu

Autom adaptation

appears.

Hold down button

Display

and turn the rotary dial until the required

value is shown.

Fig. 40 Activating Automatic adaptation

Release

Display

to save your input.

Press

Back

to return to the next higher level.

10.16 Setting switching optimisation

The following variations are possible:

Call up the service level.

GENERAL PARAM.

appears as the first main menu.

Turn the rotary dial until main menu

Heat.circuit

+ No. is displayed.

Press

Display

to call up a submenu.

Turn the rotary dial until submenu

Optimisation for

appears.

Hold down button

Display

and turn the rotary dial until the required

value is shown.

Fig. 41 Setting switching optimisation

Release

Display

to save your input.

Press

Back

to return to the next higher level.

10.17 Set switch off optimisation time

If switching optimisation is set to

Switching off

Start/Stop

this

option allows the entry of the time when the anticipated setback mode

shall start. The setting must only be changed if so required.

Call up the service level.

GENERAL PARAM.

appears as the first main menu.

Turn the rotary dial until main menu

Heat.circuit

+ No. is displayed.

Press

Display

to call up a submenu.

Turn the rotary dial until submenu

Stop optim. time

appears.

Hold down button

Display

and turn the rotary dial until the required

value is shown.

Fig. 42 Set switch off optimisation time

Release

Display

to save your input.

Press

Back

to return to the next higher level.

Input range

Factory setting

Autom adaptation

yes

Table 54 Setting range Automatic adaptation

The function

Optimisation

requires a remote control

with room temperature sensor to be installed.

The function

Optimisation for

It is not activated in the

factory.

Optimisation Explanation

Start Up

Heat-up commences before the actual switching time

if "Start" has been selected. The control calculates the

start-up time, so that the set room temperature is

achieved at the set switching point.

Switching off When "Switch OFF" has been enabled, the system

begins the setback, where possible, prior to the actual

setback time to save energy. If a room cools down

unexpectedly or suddenly, the stop optimisation is

terminated and heating continues normally up to the

programmed setback time.

Start/Stop

Both optimisation versions are used when "Start/

Stop" has been enabled.

none

Switching optimisation is not implemented if "none" is

selected.

Table 55 Switching optimisation

As the start optimisation is limited to 240 minutes, start

optimisation is not suitable for systems with a long heat-

up time.

HEAT CIRC. DATA 2

Autom adaptation

yes

6 720 802 836-54.1TL

Input range

Factory setting

Optimisation

none

Start

Stop

Start/Stop

none

Table 56 Setting range Optimisation

Input range

Factory setting

Stop optim. time

10 min – 60 min

60 min

Table 57 Setting range Stop optimisation time

HEAT CIRC. DATA 2
Optimisation
for

Stop

6 720 802 836-55.1TL

HEAT CIRC. DATA 2
Stop
optim. time

30min

6 720 802 836-56.1TL

Содержание CFB 840

























































Результаты поиска

Содержание CFB 840

Отзывы:

Похожие инструкции для CFB 840

Бренды по названию

Популярные бренды

Bosch CFB 840, Инструкции по обслуживанию

Результаты поиска

Содержание CFB 840

Отзывы:

Похожие инструкции для CFB 840

Бренды по названию

Популярные бренды