Bosch CFB 840 Скачать руководство пользователя страница 11

Страница: 11 / 56

Modules and their function

6 720 802 836 (2012/05)

CFB 840

5.3.1 Burner function

Flue gas test

Press and hold button

Flue gas test

(

fig. 11, [11], page 10) for a

few seconds.

The heating control unit operates for 30 minutes at a higher flow

temperature.

During the flue gas test, the indicators

Fault

and

Summer mode

flash

alternately.
To terminate the flue gas test:

Press button

Flue gas test

again.

Manual burner switch

Positions

Manual

and

max I + II

of the burner's manual switch are

special settings (

fig. 11, [7], page 10) reserved for contractors.

The burner may be directly controlled with the manual switch.

5.3.2 Heating circuit and DHW functions

Positions

and

Manual

are special settings of the manual switch for the

heating circuit and DHW (

fig. 11, [6], page 10) reserved to

contractors.

5.4

FM442/CMM 920 function module (accessory)

The FM442/CMM 920 module regulates two independent heating

circuits with optional mixing valves. Several of these modules can be

used in one control unit.
The manual switches on the module only have service and maintenance

functions and only affect 230 V outputs.
If the manual switches are not set to automatic, a corresponding

message appears on the programming unit, and the corresponding

indicator

Fault

illuminates.

The control functions remain operational in manual mode without any

restrictions.

Fig. 12 FM442/CMM 920

[1]

General fault,

e.g. on-site faults, sensor faults, external faults, wiring faults,

internal module faults, manual mode. The error messages appear

as plain text in the programming unit.

[2]

Heating circuit in summer mode

[3]

Heating circuit pump operational

[4]

"Mixing valve opens" (hotter)

[5]

"Mixing valve closes" (colder)

[6]

Manual heating circuit switch

e.g. for heating circuit 1 and 2

In normal operation, the manual switch is set to

AUT

Current functions are indicated by LEDs.

Position

Function

As base load, only the first stage will be

enabled for single and two stage burners. The

second stage is at zero volts. The burner

servomotor cannot be reversed. For

modulating burners, the burner output can be

increased using

and reduced using

The burner operates in automatic mode.

The burner is switched OFF. Except when the

burner emergency switch is set to

Manual

The burner operates continuously at maximum

output.

Table 8 Burner functions ZM422

In normal operation, the manual switch is set to

AUT

Current functions are indicated by LEDs.

AUT

max

I+II

AUT

max

I+II

AUT

max

I+II

AUT

max

I+II

Position

Function

The heating circuit 0 pump or boiler pump and

the cylinder primary pump are switched on.
Heating circuit 0 pump or the boiler circuit and

DHW circuit operate in automatic mode.
Heating circuit 0 pump or boiler pump, the

cylinder primary pump and DHW circulation

pump are switched off. The control functions

remain active.

Table 9 Heating circuit and DHW functions ZM422

Never use the manual switch to shut down the heating

system during temporary absence. Use the holiday

function for this purpose (

see operating instructions

for control units).

6 720 803 703-13.1T

Содержание CFB 840

























































Результаты поиска

Содержание CFB 840

Отзывы:

Похожие инструкции для CFB 840

Бренды по названию

Популярные бренды

Bosch CFB 840, Инструкции по обслуживанию

Результаты поиска

Содержание CFB 840

Отзывы:

Похожие инструкции для CFB 840

Бренды по названию

Популярные бренды