Bosch B465 Скачать руководство пользователя страница 87 | Manualshive

Страница: 87 / 115

background image

Conettix Universal Dual Path Communicator

Maintenance and troubleshooting | en

87

Bosch Security Systems, Inc.

Installation and Operation Manual

2017.11 | 05 | F.01U.311.207

Flash pattern

Function

Flashing

Indicates a communication trouble. Verify IP address
and port numbers used by the central station. If it was
running correctly and now shows this indication, check
to make sure the account is enabled in the receiver or if
there is an IP path problem preventing the B465 from
reaching the receiver.

Flashing

Indicates multiple communication errors. Check the
B465 USB status menu for additional information to
help correct the problem.

On Steady

Indicates all non IP communication troubles. For
example low, or missing battery, phone lines are off the
hook for more than 2 minutes, or there is a
configuration issue.

Tab.

11.14:

SYSTEM TROUBLE LED descriptions

POWER LED

Flash pattern

Function

On Steady

Indicates a good Input Power level.

Flashing

Indicates Input Power is low (brownout) or failure.

Off

Is in an off state during the power up sequence.

Tab.

11.15:

POWER LED descriptions

BATTERY LED

Flash pattern

Function

Off

Indicates normal operations.

Flashing (one flash)

Indicates low battery voltage.

«
...
85
86
87
88
89
...
»

Содержание B465




















































































































Отзывы:

Нет отзывов

Похожие инструкции для B465

Бренд: T-Mobile Страницы: 24

Yealink SIP-T46G

Бренд: Yealink Страницы: 8

Бренд: Samsung Страницы: 123

Бренд: N-Com Страницы: 32

Бренд: TCL Страницы: 62

Бренд: Zte Страницы: 26

Бренд: GENERAL MOBILE Страницы: 158

Бренд: Lava Страницы: 2

Бренд: Lava Страницы: 36

Бренд: Lava Страницы: 21

Бренд: Avvio Страницы: 30

Бренд: Avvio Страницы: 79

Бренд: Zte Страницы: 273

Бренд: Lava Страницы: 31

SoundStation 2W

Бренд: Polycom Страницы: 46

Бренд: Samsung Страницы: 163

Бренд: Samsung Страницы: 175

Бренд: Samsung Страницы: 186

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды