manualshive.com logo in svg

Bosch AVENAR 4000 FAH-425-T-R, Руководство по эксплуатации

Поделиться
Скачать
Bosch AVENAR 4000 FAH-425-T-R Скачать руководство пользователя страница 34

Error code

Cause of trouble and troubleshooting

10000000

General C malfunction
Possible causes:
–

– Thermal sensor fault

–

– Maximum operation duration (5 years)
of the C sensor has been exceeded.

T and C sensors are switched off; the optical
sensor is still in operation.
Exchange detector immediately.

11000000

The impedance of the electrochemical cell is
too high.
The C sensor is switched off; the rest of the
sensors are still in operation.
Exchange detector immediately.

10100000

The permissible operating temperature
(-10 °C to +50 °C) has been exceeded. The C
sensor is switched off; the rest of the sensors
are still in operation.

10011110

Malfunction due to read/write error in the
EEPROM
Detector is switched off and must be
exchanged immediately.

0000xxxx

Number of read/write errors in the EEPROM

–

Contamination

The optical initial set-up value of a new detector is stored in the integrated EEPROM during
the final inspection. The contamination value specifies by how much this analog value has
increased in comparison with the delivery state.

Warranty

Defective detectors are exchanged free of charge in the case of a claim under the warranty.

Repair

In the event of a defect, exchange the entire detector.

Disposal

Unusable electrical and electronic devices or modules must not be disposed
of with normal household refuse. They must be disposed of in compliance
with the applicable regulations and directives (e.g. WEEE in Europe).

Packaging film for the FAP-425-DOTC-R
The packaging bag used for multisensor detectors with C sensor consists of tear-resistant PE-
ALU laminated film and may be disposed of with the household refuse.
Defective detectors are exchanged and should be disposed of in accordance with legal
regulations.

7.4

7.5

7.6

34

en | Maintenance and Service

AVENAR detector 4000

2014.11 | 1.1 | F.01U.283.550

Operation Guide

Bosch Sicherheitssysteme GmbH

Содержание AVENAR 4000 FAH-425-T-R







































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды