bora PKG3, Инструкции по эксплуатации и монтажу

Страница: 26 / 44

EN
26
Installation
www.bora.com
X
Check that installation has been carried out correctly.
X
Switch on the main switch/automatic circuit breaker.
X
Put the cooktop into operation (see the “Operation” chapter).
X
Check that all the functions are working correctly.
5.10 Basic configuration
When installation is complete, you must carry out the basic
settings (these settings can be changed at any time later on).
i
You can see precise instructions on the basic
configuration and all necessary information in the
“Configuration menu” chapter of the operating
instructions.
5.10.1 Gas configuration
i
The burner nozzles, gas type, gas pressure and gas
characteristic curve may only be changed by a certified
engineer or BORA service technician. They also assume
responsibility for the proper gas installation and
commissioning.
i
Gas characteristic curve A must not be used in the case
of liquid gas (G30/31).
i
It is important that the gas type, gas pressure and
characteristic curve are set correctly to ensure safe,
failure-free operation of the gas cooktop.
i
You can see detailed information on the configuration
menu in the operating instructions.
X
Enter the settings in the gas configuration menu (see
“Configuration menu” chapter).
5.11 Initial operation
i
Detailed information on how to use the BORA
Professional 3.0 system can be found in the cooktop
extractor’s operating instructions..
X
Ensure that all appliances are connected correctly and
connected to the power supply (fused) prior to initial
operation.
O
Exception: During initial operation, the kitchen fitter may use
a temporary power supply for the control unit in order to carry
out the basic configuration (e.g. using the site power supply
during the building phase).
O
The settings made are saved and will not be affected when the
system is disconnected from the mains.
O
The final mains connection to the appliances may only be set
up by certified specialists.
5.11.1 Using the gas cooktop for the first time
i
Initial operation is possible when the gas cooktop has
been fully installed and configured.
X
Switch the cooking zone on.
The electronic gas regulator will calibrate itself (humming noises)
and then the gas flame will automatically ignite in the selected
cooking zone.
The gas flame will burn steadily and evenly.
Using the gas cooktop together with the cooktop extractor
for the first time
X
Switch the cooktop extractor to the maximum power level.
X
Switch all cooking zones to the minimum power level.
The electronic gas regulator will calibrate itself (humming noises)
and then the gas flame will automatically ignite in the selected
cooking zone.
The gas flame will burn steadily and evenly (no reignition). The
gas flame will be slightly affected by the cooktop extractor
(airflow) – this is normal.
X
Check all the functions of the cooktop extractor and cooktop
are working correctly.
X
Check the burner flame is working correctly, particularly when
the cooktop extractor is in use.
i
If the gas flame goes out, is excessively affected by
the extractor and/or the flame is not as it should
be (e.g. soot production, flame blowback, etc.), the
characteristic curve must be increased, as well as the
ventilation in exhaust air mode, if necessary, or the
return flow aperture in recirculation mode.
5.11.2 Faults during initial operation
When operating for the first time or after a prolonged period
without use or when the liquid gas bottles have been changed,
faults are possible:
The burner does not ignite. The control knob emits an
acoustic signal and the power level display flashes.
There may be air in the gas pipe.
X
Try to ignite it again by touching the control knob.
The burner does not ignite and the cooktop does not
react.
The electronic gas regulator must be recalibrated.
X
Using configuration
Ch,
reset the gas regulator.
The control knob display shows an error message (e.g.
E001).
X
Using configuration
Ch,
reset the gas regulator.
5.12 Function test
X
Carry out a thorough function test on all appliances in
accordance with „6.3 Initial operation“
X
In the event of error messages, see the “Troubleshooting”
chapter in the operating instructions.