bora PKG3, Инструкции по эксплуатации и монтажу

Страница: 14 / 44

EN
14
Installation
www.bora.com
5 Installation
i
Assembly, installation and commissioning must always
occur in line with national laws, regulations and
standards.
i
The work must be performed by qualified specialists who
know and comply with the additional regulations of the
local energy supply companies.
i
The appliance must only be used in well-ventilated rooms.
X
Observe all safety and warning information (see „2 Safety“).
X
Follow the enclosed manufacturer’s information.
X
Before connecting the appliance, check that the appliance
settings comply with local connection requirements (gas type
and pressure).
X
Do not leave small children unattended near the appliance!
5.1 General installation instructions
i
The appliances must not be installed above cooling
devices, dishwashers, stoves, ovens, washing machines
or dryers.
i
The contact surfaces of the worktops and wall sealing
strips must be made of a heat-resistant material (up to
approx. 100°C).
i
Worktop cut-outs must be moisture-sealed using suitable
means and, where necessary, fitted with a thermal
insulator.
i
External devices may only be connected to the cooktop
extractor connections provided.
i
Extremely bright lights aimed directly at the appliances
can cause colour variations in the appliances and are
thus to be avoided.
General installation instructions for cooktops
i
To ensure that the cooktops perform optimally at all
times, there must be sufficient ventilation beneath the
cooktops.
i
The performance of the cooktops is affected or the
cooktops overheat if the warm air beneath the cooktops
cannot escape.
i
If a cooktop overheats, the power is automatically
reduced or the cooktop is switched off completely (see
„4.3.3 Overheating protection“).
i
If cable protection (false floor) is planned beneath the
appliance, this must be fitted so it does not obstruct
ventilation.
Additional installation notes for Australia and New Zealand
(AU/NZ):
i
The gas hose must be inspected every 5 years and
replaced if necessary. The gas hose must meet the
requirements of AS/NZS 1869.
5.2 Checking the scope of delivery
X
Make sure the delivery is complete and check it for damage.
X
If there are any missing or damaged parts, please notify the
BORA After Sales Service.
X
Do not under any circumstances install parts which are
damaged.
X
Dispose of transport packaging in the proper manner (see „10
Decommissioning, disassembly and disposal“).
Name Quantity
Cooktop 1
Control knob 2
Operating and installation instructions 1
Cooktop mounting screws 4
Height adjustment plate set 1
Cooktop mounting straps 4
Control knob cable 2
Cooktop to cooktop extractor communication cable 1
Special scope of delivery for glass ceramic cooktops
Glass ceramic cleaning instructions 1
Special scope of delivery for gas cooktops
Cast-iron grate 2
Nozzle set G20/20 mbar natural gas PKGDS2020 1
Cylindrical/conical transition piece 1
Seal 1
Special scope of delivery for Australia and New Zealand:
Gas regulator 1,00 kPa
with test point for natural gas (NG)
1
Flexible gas connection hose, length 500 mm, 1/2”
external thread (EN14800)
1
Test point adapter for liquid gas (LPG) 1
Nozzle set G20/10 mbar (NG/1.0 kPa) – pre installed 1
Nozzle set G31/27,5 mbar (ULPG/2.75 kPa) 1
Tab. 5.1
Scope of delivery of the cooktops
5.3 Tools and aids
The following tools are required to correctly install the appliance:
O
pencil
O
tape measure or folding metre stick
O
standard or cordless drill with Ø 50 mm Forstner bit
O
black, heat-resistant silicone sealant
O
slotted screwdriver
O
size 20 Torx screwdriver