background image

 

Page 7 

3BE390692NM – 10/10 

 

 

BONNET GRANDE CUISINE 
Registered Office: 
Rue des Frères Lumière - Z.I Mitry Compans 
77292 MITRY MORY Cedex

 

 

4.   OPERATING FAILURES 

 

 
Sensor failures 
 

- E40: 1 or 2 (out of 3) core probe sensors are cut. 
- E41: 1 or 2 (out of 3) core probe sensors are short-circuited. 
- E61: Short-circuited ambient probe. 
- E62: Cut ambient probe. 
- E63: Core probe missing or cut. 
- E64: Short-circuited core probe. 
- E69: Steam boiler at +110°C. 
- E70: Short circuited boiler sensor. 
- E71: Cut boiler sensor. 

 

Other failures 
 

- E42: Maximum temperature within the electronic facia exceeded. 
- E43: Saturated steam inlet activated more than 30 seconds in steam mode. 

(Choked condenser nozzle, condenser supplied with hot water or insufficient flow-rate). 

- E45: Inoperative boiler drainage. 
- E46: Defective communication bus I2C. 
- E47: Saturated USB flash drive (in case of option). 
- E51: Set ambient temperature at 0. 
- E52: Set duration or core temperature at 0. 
- E53: Ventilation: failure to operate. 
- E67: Activated gas safety inlet. 
- E68: Capacity temperature at + 290°C. 

 

Содержание Equator 6





























Отзывы: