Bogen ORATOR Скачать руководство пользователя страница 2

CAUTION

RISK OF ELECTRIC SHOCK DO NOT OPEN

CAUTION: TO PREVENT THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE
ANY FRONT/BACK COVERS OR PANELS. NO USER-SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL.

The exclamation point within an equilateral triangle is intended to
alert the user to the presence of important operating and mainte-
nance (servicing) instructions.

The lightning flash with arrowhead symbol, within an equilateral
triangle, is intended to alert the user to the presence of uninsulated
"dangerous voltage" within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.

CAUTION

DANGER OF EXPLOSION IF
TRANSMITTER BATTERY IS

INCORRECTLY REPLACED.

REPLACE ONLY WITH SAME

OR EQUIVALENT TYPE

WARNING

BATTERY SHALL NOT BE

EXPOSED TO EXCESSIVE

HEAT SUCH AS SUNSHINE,

FIRE, OR THE LIKE.

NOTICE: 

Every effort was made to ensure that the information in this guide was complete and accurate at the

time of printing. However, information is subject to change.

WARNING:

To reduce the risk of Fire or Electric Shock, 

Do Not Expose 

this apparatus to rain or moisture.

Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as
vases shall be placed on the apparatus.

WARNING:

Only connect unit to AC mains outlet providing protective earthing connection.

NOTE:

Mains plug or an appliance coupler are used as disconnect devices from the mains and shall remain

readily accessible and operable.

CAUTION: 

These servicing instructions are for use by qualified service personnel only. To reduce the risk of

electric shock, do not perform any servicing other than that contained in the operating instructions

unless you are qualified to do so.

Always follow these basic safety precautions when installing and using the unit:

IMPORTANT SAFETY INSTRUCTIONS

1.

Read these instructions.

2.

Keep these instructions.

3.

Heed all warnings.

4.

Follow all instructions.

5.

Do not use this apparatus near water.

6. 

Clean unit with dry cloth. 

7.

Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.

8.

Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including

amplifiers) that produce heat.

9.

Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades

with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide
blade, or the third prong, are provided for your safety. If the provided plug does not fit into your outlet, con-
sult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles,

and the point where they exit from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.
12. Unplug this apparatus during lightning storms or when not used for long periods of time.

13. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been

damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have
fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate
normally, or has been dropped.

Содержание ORATOR





















Отзывы: