BodyCraft Family XPress Pro Скачать руководство пользователя страница 10

Страница: 10 / 56

ASSEMBLY

2.1

General Instructions

⚠

DANGER

Do not leave any tools, packaging materials such as foils or small parts lying around,

as otherwise there is a danger of suffocation for children. Keep children away from the
equipment during assembly.

⚠

WARNING

Pay attention to the instructions attached to the equipment in order to reduce the risk of

injuries.

⚠

CAUTION

Ensure to have sufficient room for movement in each direction during assembly.

The assembly of the equipment must be carried out by at least two adults. If in doubt, seek

the help of a third technically skilled person.

࣑

ATTENTION

To prevent damage to the equipment and the floor, assemble the equipment on a mat or

packaging board.

NOTICE

In order to make the assembly as simple as possible, some screws and nuts to be used can

already be pre-assembled.

Ideally, assemble the equipment at its later set-up place.

Содержание Family XPress Pro

























































Результаты поиска

Содержание Family XPress Pro

Отзывы:

Бренды по названию

Популярные бренды

BodyCraft Family XPress Pro, Руководство по сборке и эксплуатации

Результаты поиска

Содержание Family XPress Pro

Отзывы:

Бренды по названию

Популярные бренды