Body Solid EXM2500 Скачать руководство пользователя страница 22

Страница: 22 / 56

STEP

Be careful to assemble all components

in the sequence they are presented.

NOTE:

Finger tighten all hardware in this step. Do Not wrench tighten until end of

1 .

Attach Leg Extension Main Frame

to the 2” x 2” Front Stabilizer

using:

(1) a17 1/2” x 5 1/2” hex head bolt

(1) c1 1/2” washer

(1) b1 1/2” nylon locking nut

2 .

Attach Leg Extension Main Frame

to the 2” x 4” Upright

using:

(2) a1 1/2” x 5” hex head bolt

(2) c1 1/2” washer

(2) b1 1/2” nylon locking nut

3 .

Attach Leg Extension Frame

to the Leg Extension Main Frame

using:

(2)

(1)

4 .

Slide (1) Foam Roller Bar

into Leg Extension Frame

with (2) Foam Rollers

d13

and (2) 1” Leg Ext Foam Roller End Cap

d40

holding it in place as shown .

Attach (2) End Caps

d28

onto the top and bottom Leg Extension Frame

and (1)

End Cap

d28

onto the top of Leg Extension Main Frame

5 .

Slide (1) Foam Roller Bar

into Leg Ext . Seat Pad Frame

with (2) Foam Rollers

d13

and (2) 1” Leg Ext Foam Roller End Cap

d40

holding it in place as shown .

Attach (3) End Caps

onto the Leg Ext . Seat Pad Frame

STEP

This hardware is attached

to Leg Extension Frame

and shown in diagram

with a box around it.

M8 washer

M8 x 15mm round bolt

32 X 12 bearing

M12 X 75mm shaft

Содержание EXM2500

























































Результаты поиска

Содержание EXM2500

Отзывы:

Бренды по названию

Популярные бренды

Body Solid EXM2500, Инструкция по сборке и руководство пользователя

Результаты поиска

Содержание EXM2500

Отзывы:

Бренды по названию

Популярные бренды