Body Solid EXM2500 Скачать руководство пользователя страница 18

Страница: 18 / 56

STEP

Be careful to assemble all components

in the sequence they are presented.

NOTE:

Finger tighten all hardware in this step. Do Not wrench tighten until end of

1 .

Attach (2) Weight Stack Shims

d33

, (2) End Caps

, and (2) Frame Levelers

d32

to the bottom of Main Base Frame

, as shown .

2 .

Attach (2) Foot Caps

to the ends of 2” x 2” Front Stabilizer

Attach 2” x 2” Front Stabilizer

With

ONE BOLT

to Main Base Frame

using:

(

1) a3 1/2” x 3” hex head bolt

(1) c1 1/2” washer

(1) b1 1/2” nylon locking nut

Leave the one hole open for

3 .

Attach one Foot Cap

to the end of 2” x 2” Rear Stabilizer

Attach Main Base Frame

to 2” x 2” Rear Stabilizer

and 2” x 2” Upright

as shown using:

(2) a3 1/2” x 3” hex head bolt

(2) b1 1/2” nylon locking nut

4 .

Attach 2” x 4” Upright

to Main Base Frame

using:

(2) a3 1/2” x 3” hex head bolt

(2) b1 1/2” nylon locking nut

5 .

Attach (1) Frame Leveler

d32

to 2” x 2” Rear Stabilizer

Attach (2) End Caps

and apply the (2) Grip Tape pieces

d15

onto Foot Brace

Slide Foot Brace

into 2” x 2” Rear Stabilizer

and attach as shown using:

(1) a6 3/8” x 2 1/2” hex head bolt

(2) c2 3/8” washer

(1) b2 3/8” nylon locking nut

STEP

Содержание EXM2500

























































Результаты поиска

Содержание EXM2500

Отзывы:

Бренды по названию

Популярные бренды

Body Solid EXM2500, Инструкция по сборке и руководство пользователя

Результаты поиска

Содержание EXM2500

Отзывы:

Бренды по названию

Популярные бренды