body Power IT 9910 Скачать руководство пользователя страница 8

Страница: 8 / 20

Assembly Instructions

Hardware Required

Assembly Step 2

A.) Adjustable Pivot Bar Assembly

Each

Adjustable Pivot Bar (#13)

has three holes in it. These three holes are designed to be a fine -tune adjustment that will

allow you to shift your center of gravity, so that you can easily control the rate of inversion. Insert each of the two

Adjustable

Pivot Bars (#13)

into the slots located on the

Seat Cushion Frame (#08)

ensuring that they both line up to the top holes. For

now, proceed with these instructions and if you are not satisfied with the amount of control you have during the inversion process,

please return to this step and move the

Adjustable Pivot Bars (#13)

down to the middle hole or to the lowest hole and try again.

EACH

DJUSTABLE PIVOT BAR (#13)

SHOULD BE PROPERLY SEATED INSIDE EACH BRACKET. THE

SEAT CUSHION

FRAME (#08)

BRACKET PIN SHOULD ENGAGE THE HOLE OF EACH

ADJUSTABLE PIVOT BAR (#13)

. BOTH

ADJUSTABLE

PIVOT BAR (#13)

SHOULD ALWAYS BE SET TO THE SAME POSITION.

Screw a

Hex Bolt (#42)

and a

Washer (#47)

through the bottom of the

Adjustable Pivot Bar (#13)

and secure it with a

Washer

(#47)

and a

Nylon Nut (#49)

. Insert a

Safety Lock Pin (#59)

on the top of the

Seat Cushion Frame (#08)

as illustrated for an

additional safety measure. Repeat this process on the other side.

B.) Cushion Frame Assembly

Open the

Safety Hooks (#11)

on the brackets located on the A-Frame. With the help of an assistant, lift the

Seat Cushion Frame

(#08)

and align the

Adjustable Pivot Bars (#13)

into the two slots. Make sure both sides are properly seated into each slot. Do

not be alarm if the frame does not fit perfectly in the slot. Have your assistant pry apart the handle bars to align it for a perfect fit.

Test the

Seat Cushion Frame (#08)

by rocking it back and forth a few times. After you have ensured that the

Seat Cushion

Frame (#08)

rotates smoothly, lower the

Safety Hooks (#11)

over the

Adjustable Pivot Bars (#13)

as far as they will go. Once

the

Safety Hooks (#11)

are secure, insert

Hex Bolts (#69)

into the Pivot Brackets to lock the

Safety Hooks (#11)

in place.

Bolt

#42. Hex Bolt (M6x15 mm)

[2 Pieces]

#69. Hex Bolt (M6x10 mm)

[2 Pieces]

Washer

#47. Washer (M6)

[4 Pieces]

Nut

#49. Nylon Nut (M6)

[2 Pieces]

Others

#59. Safety Lock Pin

[2 Pieces]

IT9910

Page 6

Содержание IT 9910





















Результаты поиска

Содержание IT 9910

Отзывы:

Похожие инструкции для IT 9910

Бренды по названию

Популярные бренды

body Power IT 9910, Руководство пользователя

Результаты поиска

Содержание IT 9910

Отзывы:

Похожие инструкции для IT 9910

Бренды по названию

Популярные бренды