Outdoor LP Gas Barbecue Grill Model No. GBC831WB-C
Contact 1.800.762.1142 for assistance. Do not return to place of purchase.
3. Control knob must be in the “OFF” position.
(Figure 7)
4. Turn ON gas at LP gas tank.
5. Push and turn control knob counterclockwise to
“HIGH”.
6. Press the electronic igniter button and hold for 5
seconds to light burner.
7. If ignition does not occur in 5 seconds, turn burner
control knob “OFF”, wait 5 minutes, and repeat
lighting procedure.
8. If igniter does not light burner, use a lit match
secured with the lighting rod provided to light
burners manually. Position the lit match near side of
the burner. (Figure 8)
Important:
Always use the lighting rod provided when
lighting burners with a match.
9. After lighting, please observe the burner flame,
make sure all burner ports are lit and flame height
matches illustration. (Figure 9)
CAUTION: If burner flame goes out
during operation, immediately turn
the gas “OFF” and open lid to let the
gas clear for about 5 minutes before
re-lighting.
Turning Off
1. Turn gas OFF at LP gas tank.
2. Turn control knob clockwise to the “OFF” position.
Note:
A “poof” sound is normal as the last of the LP
gas is burned.
Cooking
1. Light burner.
2. Set burner to desired temperature
3. Place pan on center of grid.
4. Cook and adjust temperature as needed.
Cleaning and Care
CAUTION:
1. All cleaning and maintenance should be done when grill is cool and
with the fuel supply disconnected.
2. DO NOT clean any grill part in a self cleaning oven. The extreme heat
will damage the finish.
Notices
1. This grill should be thoroughly cleaned and inspected on a regular basis.
2. Abrasive cleaners will damage this product.
3. Never use oven cleaner to clean any part of grill.
4. Do not clean any grill part in a self cleaning oven. The extreme heat will damage the
finish.
Before Each Use:
1. Keep the grill area clean and free from any
combustible materials, gasoline, and other
flammable vapors and liquids.
2. Do not obstruct the flow of the combustion of LP
and the ventilation air.
3. Keep the ventilation opening(s) of the LP gas tank
area free and clear from debris.
4. Visually check the burner flames, to make sure your
grill is working properly.
5. See sections below for proper cleaning instructions.
6. Check and clean the burner/venturi tubes for insects
and insect nests. A clogged tube can lead to a fire
beneath the grill.
Cleaning Surfaces
1. Wipe surfaces clean with mild dishwashing
detergent or baking soda.
2. For stubborn surfaces use a citrus based degreaser
and a nylon scrubbing brush.
3. Rinse clean with water.
Figure 9
Burner
Flame
Slight
Yellow
Slight
Blue
Dark
Blue
Figure 7
Figure 8
Figure 10
Burner Flame Conditions
Use this chart check to see if your
burners need to be cleaned.
1-2 in.
/
25.4 - 50.8 mm
1-2 in.
/
25.4 - 50.8 mm
Normal:
Soft blue flames with
yellow tips between 1 in. - 2 in.
hight.
Needs Cleaning:
Noisy with hard
blue flames.
Has to be cleaned:
Wavy with
yellow flames.
Operating Instructions (continued)
Cleaning Main Burner
1. Turn gas “OFF” at the control knobs and LP gas tank.
2. Remove cooking grid and heat plates.
3. Remove burner by removing the fasteners securing the burner to the grill bottom.
4. Lift burner up and away from gas valve orifice.
5. Disconnect wire from spark electrode.
6. Clean inlet (venturi) of burner with small bottle brush or compressed air.
7. Remove all food residue and dirt on burner surface.
8. Clean any clogged ports with a stiff wire (such as an opened paper clip)
9. Inspect burner for any damage (cracks or holes). If damage is found, replace with new
burner.
10. Reinstall burner, check to insure that gas valve orifice is correctly positioned inside burner
inlet (venturi). Also check position of spark electrode.
11. Replace heat plate and cooking grid.
12. Perform leak test.
Cleaning Side Burner
1. Turn gas “OFF” at the control knobs and LP gas tank.
2. Remove side burner grid.
3. Remove burner by removing the screws securing the burner to the side shelf.
4. Lift burner up and away from gas valve orifice.
5. Clean inlet (venturi) of burner with small bottle brush or compressed air.
6. Remove all food residue and dirt on burner surface.
7. Clean any clogged ports with a stiff wire (such as an opened paper clip)
8. Inspect burner for any damage (cracks or holes). If damage is found, replace with new
burner.
9. Reinstall burner, check to insure that gas valve orifice is correctly positioned inside burner
inlet (venturi). Also check position of spark electrode.
10. Replace cooking grid.
11. Perform leak test.
Product Registration
For faster warranty service, please register your product immediately at www.bluerhino.com or
call 1.800.762.1142.
Cleaning and Care (continued)
