BLEMO ER21 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 48

BLEMO ER21 Скачать руководство пользователя страница 22

68

E

N

G

L

IS

H

Configurable I/O Application Functions

Analog input application functions

Input AI1 is always the reference.

Assignment of AI2/AIC

(AI2 = 0, +10 V or AIC = X-Y mA, X and Y can be configured from 0 to

20mA)

Summing speed reference : The frequency reference from AI2/AIC can be summed with AI1.

PI regulator : Can be assigned to AI2/AIC. Allows a sensor to be connected and activates the PI
regulator.
The reference is input AI1 or an internal reference rPI which can be adjusted via the BLEMO-ER21
keypad.
Parameters which can be accessed in the adjust menu :
- regulator proportional gain (rPG)
- regulator integral gain (rIG)
- PI feedback multiplication coefficient (FbS) : is used to adjust the max. value of the feedback so that
it corresponds to the max. value of the PI regulator reference.
- reversal of the direction of correction (PIC) : if PIC = no, the motor speed increases when the error is
positive, if PIC = YES, the motor speed decreases when the error is positive.

"Manual - Automatic" operation with PI

This function combines the PI regulator and reference switching by a logic input. The speed reference
is given by AI1 or by the PI function, depending on the state of the logic input.

«
...
20
21
22
23
24
...
»

Содержание ER21

















































Отзывы:

Нет отзывов