manualshive.com logo in svg

BLAUBERG KOMFORT EC DW Series, Руководство по эксплуатации, Страница: 28 / 32

Поделиться
Скачать
BLAUBERG KOMFORT EC DW Series Скачать руководство пользователя страница 28

28

www.blaubergventilatoren.de

KOMFORT EC DW

TECHNICAL MAINTENANCE

Regular technical supervision and maintenance of the unit are required to 

ensure the product long service life and non-stop operation. 

Disconnect the unit from power supply prior to any maintenance 

operations.

Warning! Consider the unit sharp edges! Fulfil maintenance 

operations in work gloves!

The recommended unit maintenance periodicity is 3-4 times per year. The 

unit technical maintenance includes regular cleaning and other works:

1. Filter maintenance (3-4 times per year).

Dirty filters increase air resistance and decrease supply air volume. Clean the 

filters with a vacuum cleaner or flush those with water. After two consecutive 

cleanings the filter must be replaced. Install dry filters only!  Contact a local 

distributor to purchase the filters stated above in the «Technical data» section. 

Dirty filters are not considered as a warranty case!

Replace humid and mouldy filters immediately!

Filter removal for 

KOMFORT EC DW600-2 / EC DW1000-4

: 

1. Remove the 5 screws and take the side service panel off. 

2. Pull the filters until they slide off the guides.

Install the filters in the reverse order.

Supply filter 

Extract filter 

Filter removal for 

KOMFORT EC DW2000-2 / EC DW3800-2

:

1. Lift the service panel latches.

2. Open the service panel carefully, supporting it with the hand.

3. Remove the filters from the unit.

2. Heat exchanger maintenance (once per year). 

The heat exchanger must be regularly cleaned to maintain high heat 

recovery efficiency even in case of the regular filter cleaning. Clean the 

heat exchanger with warm detergent solution. Remove the heat exchanger 

from the unit and flush it with warm detergent solution. Install the dry heat 

exchanger back to the unit. 

Heat exchanger removal for 

KOMFORT EC DW600-2 / EC DW1000-4

:

1. Remove the 5 screws and take the side service panel off. 

2. Pull the heat exchanger and remove it from the unit.

3. Disconnect the contact socket on the bypass wall and remove the 

bypass.

4. Remove the second heat exchanger in the same way. 

Assemble the parts in the reverse order. 

Heat exchanger removal for 

KOMFORT EC DW2000-2 / EC DW3800-2

:

1. Lift the  service panel latches. 

2. Open the service panels supporting those with the hand. Release the 

drain pipe from the side of the water heater installation and lower it down. 

Release the second drain pipe by pulling the drain pan aside. Install the drain 

pan in the reverse order. The heat exchanger removal for further cleaning 

should be made by the service department.

 

3. Fan maintenance (once per year).

The regular filter cleaning may not completely prevent the dust ingress 

into the unit, which results in the unit performance decrease. Clean the fan 

with a soft cloth or a brush. Cleaning with water, abrasive detergents, sharp 

object or chemicals is not allowed.

QF

WARNING!

Cut power supply to the unit off by turning the automatic electric switch QF to OFF position prior to 

any maintenance operations. 

Take steps to prevent re-activation of the automatic switch.

!

KOMFORT EC DW v1(6)_EN.indd   28

10.08.2015   10:11:18

Содержание KOMFORT EC DW Series

































Отзывы:

Нет отзывов