manualshive.com logo in svg

BLAUBERG KOMFORT EC DW Series, Руководство по эксплуатации, Страница: 20 / 32

Поделиться
Скачать
BLAUBERG KOMFORT EC DW Series Скачать руководство пользователя страница 20

20

www.blaubergventilatoren.de

KOMFORT EC DW

Function

Indication

5

User Menu

 To enter the User menu press 

MENU 

 in the Main menu.

 The 

User menu

 contains basic menu items and functions for parameters 

setting:

ENG. MENU

 - access to the Engineering menu. The menu is password-

protected. 

AUTO ADJUST.

 - scheduled operation setting. 

DATE/TIME

 - date and time setting. 

TIMER ADJUST.

 - setting time and speed operation on timer basis.

MOTOR HOURS

 - setting filter replacement periodicity.

EXIT

 - return to the Main menu. 

6

Engineering Menu

To enter the Engineering menu press 

ENG. MENU 

 in the User menu. 

 To access the 

Engineering menu

 enter the password. The

default setting is 1111.

 Press 

OK

.

 To change the password use the 

RESET

 

 button. 

Press 

RESET

 to clear the password field.

 To return to the User menu press 

EXIT

 

.

 If you forgot the user-defined password, see clause 11 Password Change, 

press and hold 

RESET

 

 until you hear a long sound signal (20 clicks, 

approximately 20 seconds). The default password 1111 is set.

Table 6. Operation and parameter setup of the unit (continued)

KOMFORT EC DW v1(6)_EN.indd   20

10.08.2015   10:11:10

Содержание KOMFORT EC DW Series

































Отзывы:

Нет отзывов