BLAUBERG KOMFORT EC DW Series Скачать руководство пользователя страница 13

Страница: 13 / 32

www.blaubergventilatoren.de

KOMFORT EC DW

Outside

Power supply

12 V AC

230 V AC

24 V AC

Digital input (DI)
Digital output (DO)
Analogue input (AI)
Analogue output (AO)
RS485

TE1

TE2

RK1

TE4

TE3

М4

TE5

Indoor

FS1

FS2

TE6

SM3

SM4

SM2 SM1

DD1

Symbol

Name

Symbol

Name

D1*

Supply air damper

SM2*

Exhaust air damper actuator

D2*

Exhaust air damper

SM3

Bypass air damper actuator

Supply air filter

SM4*

3-way regulating heat medium valve actuator

Extract air filter

TE1

Outdoor temperature sensor

Supply fan

TE2

Air temperature sensor downstream of the heat exchanger

Extract fan

TE3

Return water temperature sensor

Control panel

TE4

Water heater freezing protection sensor

Water heater

TE5

Duct temperature sensor

FS1*

Duct humidity sensor

TE6

Indoor temperature sensor integrated into the control panel

FS2

Room humidity sensor

DD1

Pump dry run protection relay

RK1

Plate heat exchanger

M4*

Heater circulating pump

SM1*

Supply air damper actuator

* Not included in the product, available as specially ordered accessories.

Fig. 15. KOMFORT EC DW600-2 / EC DW1000-4 / EC DW2000-2 functional diagram.

KOMFORT EC DW v1(6)_EN.indd 13

10.08.2015 10:11:05

Содержание KOMFORT EC DW Series

































Результаты поиска

Содержание KOMFORT EC DW Series

Отзывы:

BLAUBERG KOMFORT EC DW Series, Руководство по эксплуатации, Страница: 13 / 32

Результаты поиска

Содержание KOMFORT EC DW Series

Отзывы: