manualshive.com logo in svg

BLAUBERG KOMFORT EC DW Series, Руководство по эксплуатации, Страница: 19 / 32

Поделиться
Скачать
BLAUBERG KOMFORT EC DW Series Скачать руководство пользователя страница 19

www.blaubergventilatoren.de

19

KOMFORT EC DW

Table 6. Operation and parameter setup of the unit (continued)

Function

Indication

3

Fan Speed Changeover

 Fan speed setting:

Press the 

AIR FLOW

 button 

 ;

The unit has four speed stages:

 - Speed 1;

 - Speed 2;

 - Speed 3;

 - Humidity Control mode. The fan speed is regulated depending on 

the humidity setting. The humidity level is set via the Engineering menu, see 

clause 14.

  If the 

AUTO

 

 or 

TIMER

 

 mode is activated the current air 

flow value is displayed in real time operation no matter of the set air flow 

value.

 Set the desired speed using the 

  or 

 buttons.

 Then press 

ENTER

 

.

 To return to the Main menu without saving changes press 

EXIT

 

.

4

Temperature Setting

Temperature setting:

 Press the 

TEMPERATURE

 button 

.

 Select the set temperature type:

DUCT

 

 (temperature in the air duct);

ROOM

 

 (temperature in the room).

 Set the desired temperature using 

 or 

 buttons.

 Then press 

ENTER

  

.

 To return to the Main menu without saving changes press 

EXIT

  

.

KOMFORT EC DW v1(6)_EN.indd   19

10.08.2015   10:11:09

Содержание KOMFORT EC DW Series

































Отзывы:

Нет отзывов