background image

SAFETY WARNING 

 

      Always pay attention to the instructions and safety warnings below  

 
This manual contains important safety information and instructions which should be read 
carefully before operating the vehicle. For your own safety and the safety of others follow 
these rules. 
Neither manufacturer nor distributor is responsible for injuries caused by unsafe and improper 
use of the vehicle.  

 
This vehicle is not allowed to be used on public roads! 

 

Unsafe and careless use of the vehicle can result in serious injuries. The driver can 
minimize the potential risks by wearing safety equipment.  The driver must wear a 
safety helmet, goggles, gloves, elbow pads, kneepads, and firm footwear. Avoid rough 
surfaces and obstacles.  Always drive with both hands on the handlebars. 

 

 

Fuel and fuel vapour are highly toxic and flamable. Always be careful when handling 
fuel – it can burn or poison you. 

stop the engine and turn off the fuel tap, keep naked flames and sparks away  

             from your bike. 

do not smoke near your bike. 

refuel only outdoors in a well ventilated space 

clean up any excess fuel immediately 

keep children and pets away 

 

Always ride within the limits of vehicle/ rider and weather conditions to  avoid 
unnecessary accidents and injuries. 

 

Check-ups 
Shut the engine off when performing maintenance check-ups otherwise You could be 
severely injured if your hands or clothing get caught by moving parts. 
 

 

Make sure the engine and exhaust are cold before performing any inspection of this 
machine  

 

 

Riding with a chain in poor condition or improperly adjusted can lead to serious injury. 
Always, Inspect, Adjust and Maintain the drive chain properly before each ride. 

 

Failure to inspect and properly maintain the brakes increases the risk of having an 
accident. Before each ride check the brake cables and the brakes efficiency.

 

 

Riding with worn brake pads can reduce the braking performance and cause an 
accident. Check and replace brake pads according to the instructions in this manual. 

 

Using worn, improperly inflated, or incorrect tyres will reduce stability and can cause 
an accident. 

 

DISPOSAL OF UNUSABLE PRODUCT 

Unusable product become a waste and it’s desposal should be  in accordance with 
the law and any applicable local regulations. Don’t throw this product to municipal 
waste. 

 
 

Always inspect the bike before each ride (refer to the article ‘INSPECTION AND 
MAINTENANCE’). Failure to inspect and maintain your bike properly increases the risk 
of an accident or damage to the vehicle.  

Содержание Minibike Elite 14 WRS

























Отзывы: