Blastrac BDC317P Скачать руководство пользователя страница 43

Страница: 43 / 48

MODEL BDC317P DUST COLLECTOR

OPERATING MANUAL

APRIL 2008

SECTION 9

FAULT DIAGNOSIS

Dust Collectors

Prior to any repair work on the machine or its drives, the

machine must be secured against unintentional activation. Put

the machine in its Safety off position. See section 2.6.

9.1 FAULT DIAGNOSIS – DUST COLLECTOR

Fault

Possible Cause

Remedy

The dust collector

does not start.

No power supply

Check if the outlet box

carries current.

Check the socket and the

cable of the dust collector

for damages.

Have the unit checked by

an electrician.

The R.P.M. of the

dust collector

increases.

Filter cartridges are clogged.

Suction hose is clogged.

Replace the filter

cartridges.

Check and clean the hose

assembly.

The dust collector

blows out dust.

Filter cartridges are damaged.

Replace the filter

cartridges.

The compressor

consumes too much

oil.

Too low oil viscosity.

Crankcase ventilation is

damaged.

Fill with the correct oil (see

section 7.4).

Clean or replace the

crankcase ventilation.

Содержание BDC317P

















































Результаты поиска

Содержание BDC317P

Отзывы:

Похожие инструкции для BDC317P

Бренды по названию

Популярные бренды

Blastrac BDC317P, Руководство пользователя

Результаты поиска

Содержание BDC317P

Отзывы:

Похожие инструкции для BDC317P

Бренды по названию

Популярные бренды