background image

5

PRODUCED FROM SHOT BLASTING SUCH SURFACES CAN CREATE A
SERIOUS HEALTH THREAT TO THOSE WHO INHALE OR COME INTO
CONTACT WITH THE DUST. AS A RESULT, THE WORK AREA MUST BE
CHECKED FOR THESE MATERIALS BEFORE WORK CAN BEGIN.
B LAS TP RO MANUF AC TUR ING, I N C . DOES NOT W AR R ANT IT S
EQUIPMENT TO BE SUITABLE FOR, OR APPROVED FOR, REMOVING
DANGEROUS MATERIALS. IT IS THEREFORE THE RESPONSIBILITY OF
THE CONTRACTOR TO AFFIRM THE SAFETY OF THE WORK AREA AND
THE EQUIPMENT WITH THE PROPER AUTHORITIES. IT IS ALSO THE
RES PONS IBILITY OF THE C ONTR ACTOR TO WARN ALL STAFF
MEMBERS OF ALL POTENTIAL SHORT-TERM AND LONG-TERM HEALTH
RISKS ASSOCIATED WITH INHALING AND COMING INTO CONTACT
WITH DANGEROUS MATERIALS. THE CONTRACTOR IS RESPONSIBLE,
FURTHERMORE, FOR PROTECTING ALL WORKERS FROM BEING
EXPOSED TO DANGEROUS

MATERIALS. SO

, BECAUSE THE BP-9-110V

SHOT BLASTING MACHINE HAS NOT BEEN DESIGNED TO REMOVE,
CLEAN, PROFILE, OR ALTER ANY SURFACE COATED WITH OR
OTHERWISE CONTAMINATED BY DANGEROUS MATERIALS, BLASTPRO
MANUFACTURING, INC. EXPRESSLY DISCLAIMS ANY LIABILITY FOR
INJURY, ILLNESS, DEATH, OR DAMAGE THAT MIGHT OCCUR OR
RESULT FROM SUCH IMPROPER USE.

Operator and any other personnel in the work area are wearing safety glasses with side
shields, dust masks, ear plugs, hard hats, steel-toed work boots, long sleeved shirts, tight
fitting clothing, and gloves. It is also imperative for staff to tie back long hair and to
remove all jewelry.

Work area has been blocked off to pedestrians, unprotected personnel, and untrained
personnel. In the event pedestrians, unprotected personnel, or untrained personnel enter
the work area, blasting operations are to be stopped immediately.

Fire extinguishers are nearby. Also, take note of the location and the contact information
of fire departments close to the work site.

Belt guards are in working order and are present on the machine where needed.

All glass and equipment, including vehicles, are protected from steel shot. This can be
done by loosely hanging a sheet of visqueen or other protective material in front of the
glass or equipment in a curtain-like fashion. The importance of protecting glass and
equipment from steel shot cannot be overemphasized.

All floor drains have been plugged or covered so as to prevent steel shot from falling
into the drains.

This equipment is only being used for commercial purposes. This equipment is only to
be operated by professional, trained, and competent operators.

The operator is aware of his surroundings and will use common sense.

THE

OPERATOR IS NOT TO OPERATE THE EQUIPMENT IF HE IS TIRED,
DISTRACTED, OR UNDER THE INFLUENCE OF DRUGS, ALCOHOL, OR
MEDICATIONS THAT DECREASE AWARENESS!

Содержание BP-9-110v




















Отзывы: