manualshive.com logo in svg

Blade Blade mSR S, Инструкция по эксплуатации

Поделиться
Скачать
Blade Blade mSR S Скачать руководство пользователя страница 14

14

EN

Transmitter and Receiver Binding

MLP4DSM Binding Procedure (RTF)

1. Disconnect the fl ight battery from the helicopter.

2. Center all trims on your transmitter.

3. Power off the transmitter and move the throttle stick to the low/off position.

4.  Connect the fl ight battery to the control board. The control board LED fl ashes, 

indicating it is in bind mode.

5.  When the Blue LED is fl ashing, push in and hold down the left stick while powering on the 

transmitter (you will hear a ‘click’).

6. Release the left stick. The transmitter will beep and the power LED will blink.

7.  The helicopter is bound when the LED on the control board is solid blue (not blinking).

8. Disconnect the fl ight battery and power the transmitter off.

If you encounter problems, obey binding instructions and refer to the troubleshooting guide for 
other instructions. If needed, contact the appropriate Horizon Product Support offi ce. For a list 
of compatible DSM

®

 transmitters, please visit 

www.bindnfl y.com

.

Your RTF transmitter comes prebound to the model. If you need to re-bind,
follow the directions below.

To bind or re-bind your helicopter to your chosen transmitter, follow the directions below.

General Binding Procedure (BNF)

1.  Disconnect the fl ight battery from the helicopter.

2.  Refer the Transmitter Setup Table to correctly setup your transmitter.

3.  Lower the throttle stick to the lowest position and center all trims on your transmitter.

4.  Power off the transmitter and move all switches to the 0 position. Move the throttle 

to the low/off position.

5.  Connect the fl ight battery to the control board. The control board LED fl ashes, 

indicating it is in bind mode.

6.  Put the transmitter into bind mode while powering on the transmitter.

7.  Release the bind button/switch after 2–3 seconds. The helicopter is bound when 

the LED on the control board is solid blue (not blinking).

8.  Disconnect the fl ight battery and power the transmitter off.

CAUTION:

 When using a Futaba

®

 transmitter with a 

Spektrum

™

 

DSM2

®

 

module, you must reverse the throttle channel and re-bind. Refer to your 

Spektrum

 module manual for binding and failsafe instructions. Refer to your Futaba 

transmitter manual for instructions on reversing the throttle channel.

Содержание Blade mSR S






























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды